All Installation Instructions for Hotpoint Range RB757BH4CT

Broiler element was sparking

I removed oven door so i could reach easier. Then removed screws from Broiler element at the back of the oven. Pulled off connected wires. Slid wire connectors on new element and screwed bracket in.

Parts Used:

Broil Element - 240V

jeff from NEENAH, WI
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

4 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

terminal was broken due to maney uses

unscrew the terminal block,pulled the old wires out,installed the new wires installed the new block

Parts Used:

Surface Burner Terminal Block Kit

Emmett J from Winchester, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

4 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The bake element quit working.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I then connected the wires to the new element and reinstalled the two screws. A brief test showed the element worked and that was it.

Parts Used:

Bake Element - Push On Terminals - 240V

Wiley from Port Orchard, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

5 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

I broke the left drawer glide on our oven

I unscrewed to old glide and replaced it then re attached the screw

Parts Used:

Drawer Glider - Left Side

Keith from Freeport, IL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

4 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

old blackened oven racks

Replaced old with new.

Parts Used:

Oven Rack

Roger from Falls Church, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

8 of 17 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The element split open and burned out

I unscrewed two screws inside the over over the element. Then I slowly pulled the element out and unplugged the two wires attached. Afterward I pushed the element back in place and screwed it back in and was done. Sure saved $550 I thought I might have to spend on a new oven,

Parts Used:

Bake Element - Push On Terminals - 240V

Thomas from Houston, TX
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set

4 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

every thing went great

Parts Used:

Bake Element - Push On Terminals - 240V

CLYDE from SAINT PETERSBURG, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set

5 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Two sockets for electric elements and their end terminals were badly burned.

0) Take the back cover of the range off.
1) Carefully noted how the wires and the sockets were connected.
2) Visually checked that the new parts were practically identical old ones.
3) Put together the new sockets from the parts in the kit.
4) disconnect the old sockets and put the new sockets in place.
5) For each unit disconnect one old wire at the time and connect the new wire. Repeat the same for second wire.
6) Neatly bunch together the rest of the wires with electrical tape. Do not cut the wires!

That's it! It took about 20-30 minutes.

Parts Used:

Surface Burner Terminal Block Kit

Marco from Santa Barbara, CA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers

4 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Burned ou element

Removed two screws, and replaced element with a new one. Easy, works great.

Parts Used:

Bake Element - Push On Terminals - 240V

Buddy from Georgetown, IN
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set

4 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The bottom strip had become rusty and looking badly

I pulled the oven door off the hinges and took the bolts out of the bottom of the over that were holding the strip on. I then pulled the strip off and replaced it with the new on. I replaced the bolts and then replaced the door on the hinges.

Parts Used:

Oven Door Bottom Trim - Black

Carolyn from North Port, FL
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

5 of 9 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Baking element not getting hot

First my son removed the two screws that held th element in place but first please tell everyone to turn off the breaker first. My son did not and he had gotten a shock from this and burned his hand. I think this is very important first. After cleaning up his hand he then replaced the element and tested it and it worked nicely.

Thank you for your prompt delivery and the correct part.

Sincerely
Kelly Didsbury

Parts Used:

Bake Element - Push On Terminals - 240V

Kelly from Charlotte, NC
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

4 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The burner bowls were burnt through and nasty looking.

I carefully removed the burners, removed the bowls and replaced them with the new ones. Easy as pie!

Parts Used:

Drip Bowl - 8 Inch

Drip Bowl - 6 Inch

Isabel from The Colony, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

a pan was dropped on hot bake element,,bake element broke

i dd not notice at first and started the self cleaner,,,i notice the self cleaner did not work,the screws had to be sprayed with dw30a couple of times and a pair of pliers to remove screws(no wrench set)after removing screws pulled the wires out to see and removed the connection to wires,,,replaced with new bake element and replaced the screws works fine,,,by the way i am a 64 years old grandmother

Parts Used:

Bake Element - Push On Terminals - 240V