RB524*R2 Hotpoint Range - Instructions

Very easy and simple/ After making sure power supply was off, removed socket screws in back plate of element, slid old element out, attached new element and replaced/tightened socket screws on plate and new element. Power on, oven on .. heated quickly and nicely. Used oven several times since ... no problems.

No brainer. No tools. Remove burner, lift out old drip bowl, drop in new one, plug in burner, voila! Done. 10 seconds.

When the part arrived, I used the diagram provided by the website to see what really needed to be done. Keep in mind, if you're doing it correctly and disconnect the range from the power source, it's going to be dark inside the oven. Get a good flashlight or electric lantern. There are two screws holding the element in. Mine were 8MM hex-head screws, but be prepared for anything. I removed the with a socket attachment/adapter to my cordless drill/screwdriver, and the part came right out. Some insulation will come as well - don't panic. Installation is similar, just in reverse order. Pay attention to the feet on the element. Make certain they are down. Don't lean on them when you think you're finished and discover that you installed it upside down like someone I know, and have to pull it out to correct this.

Removed several screws and removed element. Replaced same. Total ten minutes.

took old element out , put new element in.very easy.

Flip the circuit breaker going to oven off, then used a 1/4 inch socket on the mounting flange bolts and the bolt head screws attaching the wires. Then used a flat head screwdriver to reattach the wires with the supplied screws and bolted the new element in place. Back to the circuit breaker flipped the switch and turned the oven on to test it, and now works fine. *be sure to remove the sticker before installation, use rubbing alcohol to remove any residue.*

remove broken heating element and install the new one

1. Cut power off. 2. Remove old element, make sure you do not lose the screws, pull the connecting posts out and we used strings on posts so they could not get lost in the wall. 3. We then replaced the new element with little of no problems, it took approximately 30-45 minutes for the whole process.

Very easy repair. 2 hex head screws to take the heating element out. Then 2 more slot head screws for the wire connections. Perfect fit and operation of the new heating element.

Ordered part, took old bake element out, installed new bake element. It was real easy.

I looked for a new terminal locally, but no one had s terminal that would fit a 40-year old range. I went on line to PartSelect and could not find my model range, so I looked through all the terminals listed on the website (about 500) but found only one that was close to mine. Mounting holes did not match, but it had 3 connectors with 220 capability, so I ordered it. I requested express shipping by UPS and thought I paid for the extra charge. When I got notification of shipment. I saw it was via ground. It went from Louisville to Jacksonville to Clearwater, FL. I ordered it on Thursday night and received it the following Tuesday night. Meanwhile, we had no stove to cook on. When the part came, it took two days to get the contractor back to our condo. He drilled new holes on the mounting box and jerry-rigged the wiring to make it fit. The range is now working, but I was disappointed in the delay in shipping which I agreed to express shipping.

Unplugged range. Removed old element from back of oven which was held in by two screws. Unscrewed the wires that were attached to old element and screwed them into the new one.

With great ease. Only thing I would have appreciated was knowing the size ofvthevrequired socket wrench. Otherwise it was easy and fun as the instructions were crystal clear.

Replacing the part was fairly simple. Do not forget to dis-connect the element from the back.

Unplugged Stove, pulled away from wall. With smaller wrenches, took the two screw-nuts off the inside back and above that hold the broiler element in place. Since it is an older stove...took the back panel off the stove with philips screw-driver which consisted of 10 screws. Once that was removed was able to unscrew the broiler element from the two wires that provide the electricity. Used the flash light when I had to unfasten the screw-nuts inside the stove because kitchen lighting wasn't strong enough.