Quick Question!

Have you ever purchased from PartSelect.com before?

Models > RAX7244KQ0 > Instructions

RAX7244KQ0 Roper Washer - Instructions

All installation instructions for RAX7244KQ0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RAX7244KQ0
1,891-1,905 of 2,002
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

grinding noise wouldnt spin

  • Customer: Johnathan from Mountain Home, ID
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I have never fixed a washer, but this website made it very easy. I watched the video so there were no surprises. I unpluged the machine and disconnected the water lines and removed the two back screws. The control panel and shell came of very easy, i then tipped the washer on to its backand removed the clamps holding the motor. The motor came out very easy and the coupler was a cinch to put in. After that I reversed the process and then the wife was happy she got her washer back, Iwas happy too because I didnt have to buy a new one.

Agitator did not work right.

  • Customer: Ernest from Randolph, NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
The installation of the new parts was easy to put in. No problem after I figured out how to do it. The parts came really fast and we were very happy with the service.

washer would not agitate or spin, even after replacing coupler

  • Customer: GEORGE from GERMANTOWN, KY
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Socket set
  • 0 of 0 people found this instruction helpful
Found input to gearcase deformed, so new coupler slipped under load. Replaced gearbox. All function restored, but machine banged harshly during spin. Discovered that "skid plate" had shifted during gearbox replacement. Remounted skid plate carefully with pry bar, correcting vibration.

water leak

  • Customer: KYLE from MT JULIET, TN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
replaced water pump

No spin cycle

  • Customer: Stephanie from Frederick, MD
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
I pulled up PartSelect, compared their advice with my problem, ordered a direct drive motor coupling for my particular model, received the delivery, and called a friend who's good at home repairs and who happens to be dating my sister. He was delighted to comply with our request (her clothes get laundered here) and he had no problem with either the repair itself or the part we ordered. Replaced the hoses, too. He said the new part had been improved over the old one, but everything fit together just like it should. Then I washed her work jeans. Success! I know this isn't what you're asking, but I was so pleased to have the correct part ready to go so he didn't have to mess around. It wouldn't have taken the afternoon, but I had to clean everything that had accumulated debris in 10 years of use as he went.

agitator not working

  • Customer: Mary from Atwater, OH
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set
  • 0 of 0 people found this instruction helpful
Removed Agitator with socket wrench, Looked on PartSelect website, ordered parts with easy instructions, received parts in two days and installed them with the help of instructions that were easy to understand. Would highly recommend PartSelect for any parts needed. Very good service and reasonable prices.

Washer spin speed became very slow

  • Customer: David from Sycamore, OH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Found this web site after reading forums on slow spins and I determined it was a clutch problem. Ordered the clutch from "Part Select", watched the 19 minute video (excellent) on changing out a clutch from this website. After 1.5 day delivery, I installed per video. Very pleased, thank you; Dave

water pump quit workding no water would drain

  • Customer: Tim from Whitesburg, TN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I was very happy the part arrived very fast and just what we needed, and service was super.. We took the old pump off slipped the new one into the slot and hooked the clips back on it and tighted it up and plug the washer back in and filled with water and it drained... We started doing laundry right away, and so far so good... Tired to leave a review but it won't let us into the site, but we would use the same company to order from again, thank you so much...

The seal was broken on the agitator cap barrier

  • Customer: Ralph from New Milford, NJ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed the fabric softner at the top of the agitator (needed a screw driver to pry it loose) and reached in to grab the barrier with my hand and pulled it out, very simple to do.When I put the new one in I put some liquid soap on the gasket and it snapped right into place.Very easy to do, all is well now, thanks Part Select.

No cold water

  • Customer: Adam from Castaic, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
I did a you tube search for "no cold water in washer" and found a video for what the fix is. Afte disconecting the power and water hoses it was Unbelievable how easy it was. Two screws in the back to open it up which I watch on a you tube video which was from part select. Then two spring clamps to open the inside and expose the water valve.. One screw and a hose clip and the valve was out. Did the reverse and put it back together..

The cogs on the agitator were broken

  • Customer: Carol from East Dorset, VT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Quick and east order of part with fast delivery

Water pump was leaking

  • Customer: Michael from Spencerport, NY
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
The repair video was great. I decided not to remove the outer cover as there is room to get to the pump if the washer is tipped back. The pump was easy to fix with the exception of the root cause of the failure. There was water getting to the pump shaft and over time it rusted and expanded in the pump housing causing it to split and leak. Once the old pump was removed, a file was needed to reshape the drive shaft to allow the new pump to be installed. Not bad on a 16 year old washer!

agitator cogs wouldn't "grab"

  • Customer: kenneth from sand springs, OK
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
pulled out the agitator assembly, put together the new parts, and re- installed them. it's as easy as it gets! ( however a little grease in the replacement kit would be nice!) took 15 min. including washing my hands afterwords.

The agitator top did not turn

  • Customer: Michael from Columbus, OH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
The Whirlpool website provided an excellent repair video, showing a step by step procedure for making this repair. I did have to clean the old parts but other than that i just followed the video. I used a socket to loosen a single bolt holding the agitator,I pulled it apart, replaced the cogs, and then put it back together.

Agitator not working

  • Customer: ROGER from VAN DYNE, WI
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Followed the directions from the video from Part Select website. Very easy, saved allot of money doing it myself. Ordered the Agitator Repair Kit and the other parts that the website suggested I needed for the repair. But when you order the repair kit you do not need the Thrust spacer or the Inner cap seal because they came with the kit. The Kit I ordered does not state that it comes with those two items, but they did with the kit I ordeded. Would order from Parts Select again. Order arrived in about 3 days on a Saturday, which surprised me that FedEx delivered on a Saturday with the standard shipping. Thank You
All Instructions for the RAX7244KQ0
1,891-1,905 of 2,002