RAX5133AW0 Roper Washer - Instructions

I am not even going to attempt to explain. The videos that were brand specific are all anyone needs to complete any repair. They are very well made. And easy to follow. Thank you for saving me a repair call!

Parts select gives you the top solutions for the problem you are having. This suggested a clutch, and upon looking at mine I could see it was displaced. I watched the instructional video, and it was spot on. It told me how to from beginning to end and it worked out perfectly. I spent about an hour of my time, spent $38, and my machine is fixed. Thank you Parts select for the free video, I couldn't have done it without it.

You fist unplug power and water and drain hoses. Remove agitator and lay machine on its back. Remove clips and water pump. You then remove clips and motor from tranny. Remove 3 bolts holding tranny and pull it and shaft from the machine exposing the brake assy. R&R assembly and reverse what you've done and you're done. machine worked like new. Always buy genuine parts they fit and work. Bob

The top agitator was not working. The top of the agitator should only work in one direction. Since it wasn't, the pawls (cogs) on the top agitator were worn. In order to repair, you need to take the top of the agitator off. Remove the fabric softener container from the top of the agitator. It should pull off. Then, remove the clear plastic cover. (clear plastic cover will have an 'o' ring on it.) Below the cover will be a 7/16" bolt holding the agitator to the washer shaft. Pull the entire agitator from the stainless steel shaft. You will need to separate the top of the agitator from the bottom of the agitator. It is necessary to separately order and replace the thrust spacer, grease, and bolt. All the other necessary parts are in the Agitator repair kit which is also necessary when ordering parts. The agitator repair kit will come with a diagram for assembly, otherwise reassembly is the opposite of disassembly. It took longer to write this installation instructions than it was to do the actual repairs.

Followed instructions supplied plus use of u-tube video. The job could have been done in less time if I had a long ratchet to begin with. Fairly easy job for a woman to do.

removed 2 machine screws a top of back plate with nut-driver, removed two Phillips screws holding control panel on with screwdriver, lifted control panel out of the way to get to tension bands holding back on and removed with small pry-bar. Pry open the back enough to remove electrical connections from Water Inlet Valve. Remove machine screw with nut-driver that holds Water Inlet Valve and slide valve out. Use pliers to remove hose from Water Inlet Valve. Reverse process for install.

I used the online video provided by PartSelect. It provides a better method of instruction than I can document.

I researched the internet and found this site. It had the diagnostic procedures and possible causes for the malfunction. I followed their procedures to get to the cause of my breakdown and also found more than one malfuntion with my machine. I ordered the parts needed late Wed. night and received them Fri. afternoon(week of big snow storm). I was impressed, both with the great service that this site has provided and the very quick delivery service. Also, the price of the parts are very reasonable.

Replaced upper agitator and included the Agitator Repair Kit. Kit had all the washers needed for replacement of the upper agitator. Saved on a new washer replacement. Items were delivered together on same delivery truck. Items were ordered day apart. Thanx.

The repair video was very helpful and exactly right. The most difficult task was removing the old pump. It had apparently seeping between the motor shaft and the pump coupler for some time and had rusted the pump to the motor shaft. I had to aggressively grip the pump housing with the channel lock pliers and wrench it back and forth to break it loose. I took a file to remove the rust build up from the motor shaft before installing the new pump. Washer works fine.

Luckily enough the washer shown in the demonstration is my exact model, which eliminated any variables I may have come across. The repair was relatively easy and probably could of been done in less time but I took every step slowly to avoid breaking something or leaving something unattached. For the money and time spent on this repair I would certainly recommend this for anyone with a similar issue. After taking the machine completely apart, i found that the suspension pads were still properly functioning. Since i had already purchased them with the tub wear pads, I changed them anyway. The trickiest part for me was pulling the outer tub out because the shaft on my unit was very rusted had a considerable amount of buildup on it. During this step I was very careful to remove all the build up because there is a single rubber seal between the center opening of the tub and the motor shaft. After I made sure the shaft was completely smooth and there were no protrusions I gently rocked the tub back and forth while applying pressure from the underside of the tub, all the while making sure that the seal didn't fold in on itself or stretch in any direction. Other than that, the repair went very quickly and easily . The spanner wrench is a must !!! I actually found it on amazon for about 6 dollars and I'm positive I will find another use for it somewhere down the road. I owe a big thank you to Steve. (the guy in the video) and everyone else from parts select for making laundry day in my house tolerable again !!!

Pull out fabric softner dispenser to see bolt assembly. Use 7/16 socket and 12 inch extension. Hold bottom agitator. Unbolt top agitator. Remove dogs and cam assembly. Replace with new dogs and cam assembly. Reattach unit and installation is complete. Takes less than 15 minutes.

followed on line instructions. My wife didn't even need my help but to hold the flashlight.!!

Had a lot of corrosion on the shaft area and had a hard time removing the inner tub but after some WD-40 and unprintable words and labor it popped off. Cleaned everything up, shaft, inner drum and outer drum. After that everything was a piece of cake. Thanks for the help!

It was simple, unbolted the inside laid it down on its back, took four bolts how and replaced parts and reversed the steps. It was super easy and You guys was on top of the shipping. Wife is happy! saved $500!!!!!!