RAS8245EQ0 Roper Washer - Instructions

watching the video was a great help, not a perfect match as mine but enough information to get the job done! parts were cheap & they shipped fast. keep coming with the great videos!

After i pulled the motor off the washer, i found the coupling that was busted,removed it and put on the new one i got from you and just put everything back together again and the machine is operating as good as new again.

watched the repair video on u-tube and followed it. Had trouble separating the top agitator from the bottom agitator after removing it from the washer. I tapped the 4 white tabs on the top with a hammer and screwdriver. Top and bottom separated after that.

My washer leaked water in after wash cycle and cloths were wet after spin cycle. The cause of problem was defined in Parts Select trouble shooting guide. Replacement was just as the video described, except this model had two screws on front of control panel and the panel tipped back on hinges. Look at both sides of washers, so when you reinstall the body you know how it should look against the back panel. I didn't slide the whole washer body off, just tilted against a wall. Also, it's not necessary to get behind the washer, so the repair can be done in a tight laundry rooms like mine.

I noticed the top wasn't spinning. I took the cap off the agitator and looked inside it. Sure enough the directional clogs were broken. I had no idea what to do. I went online using my phone and discovered partselect.com With their wonderful help I was able to find out what part I needed and order it right from my phone. It only cost me $10 bucks to get it delivered to my house and it shipped in 3 days. I am 21 years old and this was my first washer. Thanks to part select I can keep my washer. Partselect saved me well over $150 dollars plus labor. I will definitely use partselect again!!!

well my Dearest Kenmore washer was vibrating badly so i looked the part in yoursite of parts select it diagnosed it i ordered the 2 different supension pads relaced then and now my Dearest kemore washer works like new again Thankyou Parts select for all your help and the price was perfect...

Followed an online video. Very informative.

Video's on parts select are a big help. Just followed the instructions. Only slight problem was the coupling's do not slide easily onto the shafts. I had to use a little lubricant and put a wood block across the opening and tap with a hammer. Maybe a little more than a tap. Also when I was ready to test the repair I found the washer would not stop filling. After much checking I found out on another repair site that the shutoff requires a certain water pressure to work properly. I hadn't opened the faucet fully. Once I did everything worked properly.

Easy, popped cap off top of agitator with edge of knife. Removed bolt from center of agitator,pulled agitator up from shaft. Removed old,worn cogs,replaced with news cogs and reassembled. Tightend with bolt . Replaced cap and bang ,works like new.

Followed the online instruction video. The video was very easy to follow.

Removed top of agitator(where softener is added, just pulls off), removed agitator cap barrier with needle nose pliers. Unscrewed visible center bolt with nut driver, pulled top part of agitator off(firm pull). With pliers pulled out cog assembly, replaced cogs in assembly. Holding top part of agitator upside down placed cog assembly back into agitator and then placed agitator back into washer so cogs don't fall out. retighten bolt.

very easy I followed the Parts Select video that's posted at the site,and covered the replacement very good.Thank You very much.

Removed the actuator cap which gives you access to the screw that holds the clutch dog assembly in place. Once the screw is removed the assembly lifts right out. The clutch dogs have a small retaining band that holde them in place. Once removed the dogs slip right out. Replace the old dogs and reverse the order of the removal process. Very easy.

pull off softener dispenser, pop off agitator cap by inserting straight screw driver into small slot, remove bolt inside agitator with socket wrench and long extension, pull agitator straight up off shaft, place agitator on floor, with feet holding bottom half pull top half apart from bottom half by pulling straight up, note direction of old cogs remove and replace with new, reassemble

Pulled out washer I was going to take back off then found out all parts are on bottom. Looked and found you folks on the internet saw video ordered parts. Made repair did 5 loads heard bang and it was all over. The coupler gave out after all 20 years . The is something else that caused coupler to fail. I will keep at this repair and make it good. But in the meantime. I will purchase a new washer but. My wife wants her old washer repaired. So I better get it right. Thank you for the quick delivery of parts I will get all parts from you folks.