Models > NBXR333EG0WW

NBXR333EG0WW Hotpoint Dryer - Overview

Get Parts and Repair Help for NBXR333EG0WW

If you know the dryer repair part you need, you can browse the list of all parts on the NBXR333EG0WW, or you can search by name or part description. You can also find your part by where it is located on the NBXR333EG0WW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for NBXR333EG0WW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the NBXR333EG0WW [Viewing 4 of 4]

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$3.94

Drum Bearing Slide

Sold individually. There are 2 per dryer. They attach to the outer-most sides of the bearing. Manufacture recommends to replace both slides at the same time.

$6.05

Drum Bearing Slide - White

Sold individually. There are 2 per dryer. They attach to the outer-most sides of the bearing. Manufacture recommends to replace both slides at the same time.

$5.62

Duct Felt Seal

May differ in appearance but functions same as original.

$4.05

D-Shaped Knob Insert Clip

Sold individually.

$21.23

Drive Belt

This drive belt is 89.5" long.

$48.46

Rear Drum Bearing Kit

This rear drum bearing kit comes with a shaft, bearing and installation instructions. The bearing plate comes with a slot in it for the ground strap. Helps keep your dryer running as smoothly as possible with as little noise as possible.

$34.19

Lint Filter and Frame

This filter collects lint as it passes through the dryer vent.

$4.61

Timer Knob

This knob will accept a D-shaped shaft.

$16.50

Idler Pulley Wheel

A dryer's idler pulley wheel serves to help the belt to rotate the drum.

$10.14

Door Handle - White

This part is on the outer door of the dryer.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Due to over loading of the dryer the drum ruined the slides and was making a bad noise due to plastic rubbing plastic

  • Customer: Matthew from Plainfield IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 525 of 540 people found this instruction helpful
It was pretty easy. After already taking apart the dryer to install a new belt I knew exactly my plan of action. I removed the two screws that hold the top panel of the dryer to the front panel. I then removed the top panel and removed the screws that hold the front to each side panel. I than pulled the front away from the cabinet and drum. I put the ne... read more

Intermittant squeaking noise

  • Customer: Mark from Addison IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 438 of 513 people found this instruction helpful
Basically, I followed the same steps a prior person posted.
1.Removed the two screws inside the door, on the top part of the opening.
2.Lifted up and removed the top.
3.Removed two screws holding the front panel in place.
4.Held up the drum while removing the front panel. I carefully turned the panel so I could get at the drum bearing wit... read more

Heater element went out

  • Customer: Brian from Clinton MO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 100 of 120 people found this instruction helpful
First of all, unplug the dryer. I removed the two screws on the front of the cabinet to remove the top. I then took out the screws to remove the dial panel. Release the belt for the drum through the access hole in the rear of the dryer. Remove the front cover and pull the drum assembly out.

Remove the element disc from the rear of the housing... read more