Quick Question!

Have you ever purchased from PartSelect.com before?

Models > NAV5800AWW

NAV5800AWW Amana Washer - Overview

Get Parts and Repair Help for NAV5800AWW

If you know the washer repair part you need, you can browse the list of all parts on the NAV5800AWW, or you can search by name or part description. You can also find your part by where it is located on the NAV5800AWW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for NAV5800AWW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$10.08

Adjustable Levelling Leg

Sold Individually. This adjustable leveling leg comes with a stop nut.

Order within the next 46 mins and your part ships today!

Drain Pump

This pump is attached to the motor and helps expel water from the washing machine. It is activated after the spin speed is maintained for a specific period of time.

$63.50

Water Inlet Valve Kit

This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount o...

Order within the next 46 mins and your part ships today!
$27.04

Brake Pad Kit

This brake pad kit contains three brake pads and six installation screws. Helps to bring a rotating cycle to a stop.

Order within the next 46 mins and your part ships today!
$19.05

Standpipe Adapter

This part helps stop the washer from overflowing.

Order within the next 46 mins and your part ships today!
$124.51

Triple Lip Seal and Hub Kit

NOTE: Before ordering, please make sure this is the correct kit for your appliances Model#.

Order within the next 46 mins and your part ships today!
$28.58

Friction Ring

Order within the next 46 mins and your part ships today!

Plastic Washer

This washer is located between the brake and transmission drive pulley.

$4.79

SPRING- CO

Order within the next 46 mins and your part ships today!
$7.93

Screw

1/4-20

Order within the next 46 mins and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Washer made loud noise on spin only

  • Customer: Donald from Glassboro, NJ
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
  • 45 of 58 people found this instruction helpful
Removed agitator, inner and outer tub, balance springs, motor assembly,transmission to get to bearing and seal in tub bottom. read more

Water leaking on floor from "mysterious place underneath washer"

  • Customer: Bryan from Chicago, IL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Socket set
  • 36 of 41 people found this instruction helpful
Water was leaking on the floor during the wash cycle and especially during draining of the washer. I removed the front panel at ground level and watched while draining after a rinse.

I t was obvious that water was spraying from a hole in the rubber end of the hose (the hose is a fused assembly of a plastic section and a rubber section).

read more

Bad shaking During Spin Cycle

  • Customer: Gary from Park Ridge, IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench set
  • 31 of 47 people found this instruction helpful
firsted layed washer back On A Angle For Easy Acess To Motor Removed Both Hoses And Four bolts pulled Motor Assembly out replced belt @ idler Pulley Reinstalled Motor. read more