MSD2651HEW Maytag Refrigerator - Instructions

I used the video on your website. It made me feel very satisfied that I was able to do it myself!

I unplugged the fridge. Then I removed the ice bucket. Then I removed the ice maker using a 3/4 socket to separate the connections and then used a small screwdriver to separate whatever connections were left. Then I installed the new ice maker and checked its level. Everything now works fine.

I removed 2 screws and lifted out the old part and replaced it with the new one, I am 79 years old and it only took about 25 minutes to have ice cubes again.

Used the butter knife to pry the old switch out, it is a snap in switch so there is a small keeper on the bottom that needs to be pushed in to pop the switch out. Un hooked wires by pulling them off of the terminals (won't shock you) and put them on the new switch and popped it in

There were 23 parts to be removed in order to replace part. So I printed out a diagram of the parts off the computer and the labled each part on the diagram with its name. I laid them all out in order and patiently re-assembled the ice maker. When finished, I gave a cheer!

Popped out the old one......plugged in the new one and popped it back into place. My wife was happy in have light again in the fridge!

Put the new one in its place easy

Used a heat gun peeled off the old façade. Upon inspection 2 of the buttons were broken pushed through. I used black electrical tape and a dab of gorilla glue to fix the buttons, Stuck the new façade over it and it works great. The only problem I placed the tape over the LED lights for 2 buttons. Now we listen for the click instead of looking for the light.

turned off freezer unplugged ice maker ,unscrewed 3 screws, removed ice maker,wiring harness and wire that goes up and down to control ice maker. installed all in reverse put back in and turned on waited and waited no ice ,theres a little control valve that let's the water in as well that was shot as well had to go get one at a local shop fairly interchangable just pull the other out and take with you,or just order one with your ice maker if you have the fridge out you might as well change it as it's just as old as the ice maker as well .everything pumping well,like never before, tons of ice all the time also put in filter on the water line as well really good tasteing ice now.

Removed and replaced part...

Grind rivet head off , install rivet tap end

Initially thought I could repair switch, but then discovered spring was broken. Ordered the new switch (Parts Select is very efficient - received switch in 3 days). Was encouraged by the posts regarding the switch installation. I had some difficulty removing the old switch. Used a pocket knife to ease the switch out of the hole to reveal the clip/spring. After noting the clip/spring location I used a small flat-blade screwdriver to release the clip. Even though I released the "molded" clip/spring(be sure to note where the spring is on the new switch and release it on the switch it was tight in the hole and had to use pliers to carefully remove the old switch. After removing the old switch, used pliers to gently remove the wire leads. Then install the leads on the new switch. Note the orientation for replacing the switch and gently feed the connecting wires into the hole so they won't kink or prevent the switch from entering the hole. Install the switch noting the clip/spring location and the orientation of the lever that the door closes on to turn off the light. Be sure to put it in without binding at an angle. Thanks to Parts Select for this service! I'll definitely be back.

After unplugging the refrigerator, I removed the lower rear access panel that exposed the condenser and the overload/relay start capacitor with 1/4" nut driver (6 total). Next, I unplugged the wire harness and spring loaded keeper with needle nose pliers. Then I pulled the overload/relay start capacitor out of the 3 pronged male receptor located on the side of the condenser and plugged in the new one. Replaced the keeper, plugged the harness back in, and replaced the panel. Very easy fix.

The fix was relatively easy but I could not get 2 of the screws removed. They were in very tight and I didn't have the right tools. Also, in the Amana refridgerator, they are in a "difficult to get at" location. I called my plumber friend and he helped me. Once the screws were out, the rest of the job went very smoothly as others have described. We took out the bad icemaker and reconnected the new one to the existing harness. I had ice in an about an hour. Thanks so much, PartSelect. The delivery was quick and the install was as many described on your website. You provide a wonderful service for the "do it yourselfer". Terri

Ordered parts from Parts Select. They were here like overnight!! Unreal. Supports just slipped in. Absolutely easy. This was my first order ever from Part Select but have a feeling it won't be my last. Parts were here so fast I did not know what had arrived until I opened the package as I had not expected them so quickly! very satisfied.