Enter the code TAKE10OFF at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on May 28 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
lights wouldn't come on/work in refrigerator
Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80...would have been at least $100 to have a repair person come to the house!
Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!
Light switch wasn't working.. As I would close the door I would notice our frig light wasn't going off...
I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull the connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!
inserted a knife between the switch and the plastic interior in order to pop the switch out. then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.
The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!
changed the light bulb still would not work so I figured it was the switch sure enough.
I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.
Door gasket not sealing allowing ice/ frost to form around and inside the door.
It was easy to take the door off by taking the two screws (located on the top of the freezer) off the top hinge and lift the door up off the bottom hinge. I took it outside and laid it on a table. Removed all the screws and took off the panel so I could remove the old gasket and clean the door and panel. The inside of the door was full of ice so we removed that and the insulation which I replaced. My wife then put the new gasket in the dryer on medium temp for about 5 minutes. We slipped the new gasket on the panel and lined it up on the door and screwed it back on the door. Then we put it back onto the freezer bottom first then replaced two screws on top hinge. Shut the door and use a blow dryer on the gasket with the door closed to make the gasket seal / conform to the door/freezer until there are no gaps between the gasket and the freezer. Note: Once the ice and water are out of the door the door doesn't weigh nearly as much as it did. Also
use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks
Ordered the leveling bolts, very fast shipping, parts correct as shown. Purchased a condo by the shore, frige had no levelers, they went in smoothly & was done in no time. Steve
Loosen the two bolts for the door top hinge. Make them loose enough so you have room enough to lift the door off its bottom hinge. But befor you do that use a marker to trace around the top hinge location, makes it easy to set it back correctly.
Take the door and lay it down on the floor, I used a coffe table to allow for the door handle.
Remove all the screws holding the seal on. Note: it’s likely the bottom screws are rusty so get some replacements before doing this job.
Remove old seal and fit the replacement. I installed the four corner screws first to get the seal aligned.
Install ALL screws before tightening, this aids seal alignment with the holes in the door.