Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Door Catch part had fallen out,/ was missing
Received your parts, Popped them both right into place, Even though only one side needed to be replaced, I wanted them to match up. It was amazing how easy this was. My husband was quite impressed I had ordered these rather then look for either a new or used dryer from some other source.
I can't believe I waited so long to find this part and do this. I got the package very fast, opened it, took the piece to my dryer and popped it into place with my fingers. It worked perfectly! this took all of two minutes and saved me from having to hold the dryer door closed with a stick. Thank you, thank you!!!
This repair was a cinch. Pliers to pull out the metal piece and a screwdriver to pry out the 'catch' part in the door. Both replacement pieces went right in. I cannot believe how easy and CHEAP this fix was, and I'm so glad I found this site!! I figured I would have to call a repairman and pay big bucks, so I put it off, but the door was getting worse--slamming it so hard to keep it shut. Again, thanks for this great site.
I did NOT have to repair the latch on the actual door, just the small metal piece that it hooks on (on the dryer itself) and it took about 10 seconds to.....do it myself. Just used needle nose pliers so squeeze the piece together and fit it in. thanks
Since the old part had fallen off of the appliance, all I needed to do was reattach the new parts, by sliding the hose onto where the water comes through and then attach the hanger to the top rack of the dishwasher. It was very easy to do and required no tools and took about a minute to finish.
The old catch on my dryer door was gone and I was keeping the door closed using tape. I ordered the part and it arrived with no hassles in about 5 days. The repair was too easy. I just popped the new catch in place. It took all of about 30 seconds to complete using no tools. I wish all home repairs were this easy.
The first step was to read the other repair stories. The tips on using the hairdryer to "warm" up the part to make it more pliable worked like a charm. A little bit of dish washing soap on either end and just like that the repair was done. (I had to run the rinse cycle twice to get rid of the bubbles) I pulled off the old tube, which actually had fallen off by itself, and slipped on the new one. I probably saved $75 on a service call. Isn't the internet a wonderful thing!
First I removed the pins to take out the dish rack. One pin on each side. Then I removed the old tube that slid off I then rubed a small dabe of lubercant on the new tube and connected it to each end opening. They slid on with litte force and no problem Thank for helping me to locate the correct replacement and for the fast delivery.
With a screwdriver I released the snaps that held the old seal on place, cleaned the area and then simply snapped the new seal in. The remarkable part for me however, is that I placed the order on December 21st @ 3PM (in way-upstate New York) and to my utter amazement it was delivered to me the very next day December 22nd @ 9AM; in plenty of time to reach my wife's deadline. Wow-Thank-You!
PartSelect sent me three different door catches with instructions for choosing the correct one. I did choose and simply inserted it into the slot and voile! All finished and it works great now! PartSelect had the part delivered the day after my order was placed. I would suggest doing business with them to anyone asking who they might contact for a part. I especially appreciated the ease of identifying and ordering from them. I was able to do all of this on-line via their website.
Original tube had started splitting --dishes not clean
I read the repair stories. Did not remove anything but the old tube. Used hairdryer to heat one end, pushed it onto front opening; heated other end, pushed it onto back opening. Took 5 minutes. Saved estimated $196 service call, parts,labor. (NOTE--I caution against using petroleum-based products like vasoline -- cause rubber to deteriorate. Hairdryer is the best solution.) Grannie in Houston TX
I used a screwdriver to remove the old part and pushed the new part in with my fingers, it was very easy. If I could do it, anyone can. I was a lot cheaper then having a repair man come to house. I am very glad I found your site online, I will definitely be using your company again.
I heated the ends of the tube in hot water and slipped it on the round end first. I was then able to slip the other end on. The secret to doing this repair is working fast while the rubber is still pliable.
Remove power, either unplug the unit or locate and turn off the circuit breaker. There is power under the dishwasher even if it is not running.
Use the nut driver to remove both lower panels to gain access to the bottom of the dishwasher.
I suspected the overflow switch and used the ohm meter to discover the resistance of the switch, with no water in the washer, measured anywhere from a couple of ohms to 40 ohms or more and of course it should be less than one ohm.
There was no sign of any leakage or other problem so I wanted to keep the job simple and replace only the actual micro switch.
Problem! The micro switch is mounted on the back side of the float stem kit and visibility is severely limited. About all you can see are the switch terminals and the head of the phillips screw that holds the microswitch on the rest of the float stem kit.. You'll definitely need a small mirror.
I first pulled the wires from the microswitch terminals. Then I used a small phillips screw driver to remove the screw holding the switch and the first thing that happened is the small white float lever fell out. (I didn't know that it was even there because of the poor visibility. Ugly surprise!)
I spent 1/2 hour or more studying how the lever went in and found that the cirular end of the lever fits into a circular depression in the assembly body and was HELD IN BY THE SWITCH. (Now it's really getting ugly!)
The problem then is how to get the lever back in place and have it stay there while placing the micro switch back in place. There just isn't any easy way to do that. If only the switch and lever were one piece it would have been so simple.
Aha!
I placed and aligned both the lever and the microswitch on the float assembly body that I received. Using a couple of small pieces of electricians tape I taped the microswitch and lever together so they were one piece. Then I carefully (very carefully) removed the switch/lever "assembly" that I made and eased it into position onto back side of the dishwasher float stem assembly body. When the switch is almost in place there is just barely room to get the tip of your finger in there and seat the rounded end of the lever into the depression. After seating the lever, carefully replace and tighten the phillips screw holding the switch in place. Then remove the electricians tape.
Replace the wires on the micro switch terminals, replace the front panels, put your tools away, and by golly, you're done.
This repair is not for the faint-hearted nor for those with fat fingers or who tend to be klutsy. It took me three or four attemps and a couple of hours to get the microswitch and float lever into place. But I think it was worth it as I didn't have to remove the dishwasher, play with water lines, or remove the full float assembly thus avoiding creating other problems that might likely result in water leaks and additional repairs..
If you decide to try this repair, good luck. It can be done but it is tough.