MHE11RDQ6 Microwave - Instructions

1. Removed cabinet screws (10-15?). 2. Removed cabinet. 3. Removed top interlock switch which actually was not defective. The press clip connection appeared as if it had been arcing for quite some time and the corrosion created resistance sufficient to prevent the current from getting through the switch. 4. Replaced switch anyway but broke plastic retaining clip despite every effort not to do so. Reset broken clip with super glue. 5. Reassembled cabinet and appliance is in good working condition.

Problem would come and go. Found service schematic inside unit. Perform all the suggested tests. One possible solution was the primary interlock switch shown on the schematic and a check found the switch stuck. It would free up some times but would stick again in the open position. Ordered switch which was a simple plug in unit.

I had previously removed the old grill vent and filter, so the hardest part of the re-installation was removing the new parts from the shipping box. Once out, the filter dropped in place, the new grill snapped into place and after tightening two screws the work was done. Kudos to Partselect for availability of these parts for a 15 year old appliance and for fast shipping (ordered Sunday, received Wednesday).

Replaced bulb by: 1 pulling plug on microwave to make sure not hot - no power; 2 used needle nose pliers with head part about same size that fit inside of socket; 3 opened pliers and held firm against broken metal part; keeping pressure of pliers against broken metal part of light bulb, slowly unscrewed the broken part from socket using firmly held opened pliers. The rest was a cinch...just screwed in new light bulb, plugged in microwave and viola - there was light once again.

It was a bit awkward because the microwave is mounted over my stove. I had to twist around and install the bulb and then replace the cover. It was a bit uncomfortable. It took me about 10 minutes to complete.

Removed 4 small star head screws from back of microwave, lifted body off, removed blown fuse and replaced with new one (found where cord enters). This model is stainless inside and out and I like it a lot. It is also sold by Daewoo and a few other manufacturers.

I mistakenly thought I had to remove the microwave to get to the back, not so. I would have had access to what I needed to unscrew; but I have to admit the hassle of taking it down and putting it back equals having to work on it attached to the shelf-your call on how you do this. I unscrewed the front top to remove the vent piece that is across the top front of the microwave. This will reveal the control panel screw. (While you have the vent removed you might want to clean the vent and the exposed filter.) carefully lift and pull out control panel. I unplugged a piece as the wires were tied tight. It will not completely detach, so carefully tip it back from exposed insides. The fuse is not clear but white with silver ends so look in upper right for it. I popped it out and replaced it. Replugged the wired part to cover and carefully fit tabs in and slide down to secre. Replace screw, replace vent piece and secure screws on top of microwave. I plugged it in to test before putting it back above my stove.

Piece of cake. One screw to release the dropdown light diffuser. Just remember, the you're screwing the new bulb in from a reverse perspective. Also this site sends the correct part the first time.

Put s pot under were you take the screw out.If you drop it you can get it easy

Finding the part was the most difficult as this is a very old microwave. I spoke to a really nice lady and we figured out that even though it was not the exact dimensions of my previous film that it would certainly fit since it was just a little bigger that what I had. Once I got it lined up correctly, it was really easy to put on after I removed the backing and took off the old film which wasn't difficult either.

Called parts select and discussed the situation and they identified the correct replacement shelf. When I received it, I just pushed it into place (the edges of the shelf are coated with a rubber seal) and it is there. The unit looks like new. It was great to be able to find a part for an appliance from 1988!

I first pulled off the vent cover above door of microwave and was originally just cleaning grease and dust around my built in microwave. i never even new tthere was afilter inside the vent cover. The cover comes off by unscrewing a couple of screws and tugging gently not to break anything else that may be attached. slide out the filter. order another through this fast delivery and you pretty much do the reverse to place it back in.

Really easy for a 75-year old female; just spent more time reading the online manual than actually installing the light bulbs to find out where to access the light bulbs.

Turn off power supply at breaker . Replace old bulb with new bulb .

We needed a phillips head screw driver to remove the single screw holding the light bulb cover in place.
Removing the old bulbs was a little work, because they had come loose from the sockets. We unplugged the microwave, so we could grip the sockets with a tool. I think my husband used a needle nose plier for this.
The new bulbs screwed in easily, and then we refastened the light bulb cover with the phillips head screw driver.