Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Putting the drawer glides on was easy. My range drawer did not have any glides on so my drawer would fall out. The drawer glides popped right on the drawer. The glides for the track were easy to screw into the body of the range. I had to bend the tracks up a little on each side with a pair of pliers. One glide would go onto the track and the other one would go on top of the track. After bending them a little I was able to push them onto the track.at the same time.
very intermittent oven won't light. Can hear gas and spark but won't light when spark isn't at ignitor tip (shorting somewhere before the tip)
Remove; Bottom drawer- pull open and lift up slightly when fully open then pull the drawer the rest of the way out. Unplug ignitor terminal- there is a small tang inside the terminal end that needed pressed out of the small hole of the ignitor, with a pick. Oven racks. Oven bottom- 2 long phillips screws at the back. lift the back up 1st then the front comes up and out. Burner diffuser- 2 small phlilips at front (they only prevent the diffuser from sliding, they don't screw into anything). slide diffuser forward out of the notch then lift the front up. pull rear tabs out of the notches to completely remove. Ignitor- two 8mm (5/16) bolts holding ignitor to burner. pull ignitor out of guide holes. Reverse to install new ignitor.
Oven lamp socket had broken center electric tab - failed.
1993 model oven, built in wall model, so didn't to remove oven for the normal rear access to replace the lamp socket. As someone else posted, replacement can be done from inside the oven -- BUT the socket removal was more complex than just 'twisting it out.' But below worked! (1) Turned off oven power at circuit breaker panel. To facilitate working in the oven compartment, removed oven door (2 screws on back of door), raised the over door almost closed, put 2 large nails through the hinge holes when they lined up. Lifted the door out (heavy ~20-25 lbs) and put aside. (2) Put work light inside oven. (3) unscrew glass socket lens and the bulb). (3) Using inspection mirror, studied the inside of the socket to determine that its lock tab type and locations -> were on left and right sides of the socket. These tabs needed to be bent in, but they were each held out by a small circumferential length of think metal, a tab about 3/16" x 3/8". These small tabs could be moved/positioned by just finger friction, with a little start with a screwdriver tip on their edge! I got an end positioned to put sharp screwdriver under that end, then pried it (bent it) inward a short distance. Enough to use needle-nosed pliers to pull it completely out - came fairly easily. Repeated on other side of socket. (4) Then, with pliers, bent each of the 4 locking tabs inward a short distance, Used sharp tool to get one socket edge lifted a small amount; then use mini-pry bar and screwdriver to gently pry around the socket in steps, working evenly around its edge. At about 3/8", it was free. Lifted it inward gently so as not to damage the insulation of the 2 wires attached to its rear. Noted the direction of the wire tabs was straight up (keep same orientation on new socket). (5) Needle-nosed pliers on each connector to gently work the connectors off their socket tabs. Note one tab is larger than the other. Keep the wires inside the oven compartment. Don't damage the insulation. (6) Pushed the wire connectors onto their respective new socket tabs. Aligned socket with the tabs upward, and inserted it, careful to nurse the wires back into the oven wall hole; press socket into the hole, pushing it in evenly and firmly until flush. (7) Pushed in the new type bulb that came with new Socket. Turned on power, and light came on. (8) screwed on new glass cover. (9) Lifted oven back onto the hinge prongs. (easier with two people to get the prongs aligned and into their door slots.) Worked door left and right to get it to lower down fully. Removed nails, lowered door, and put its 2 screws back on. (10) Poured a glass of wine.
I ordered the exact replacement igniter through the website. I removed the oven bottom plate and the flame spreader to gain access to the igniter/burner assembly. I removed the burner from the oven to access the mounting bolts for the igniter. I replaced the assembly into the oven and reconnected the igniter wire and it was set!
Oven temperature was WAY off, sometimes 50 degrees.
Turned the breaker off. Removed the racks, pulled the oven out and removed the back. Disconnected and unscrewed the old sensor from the back, connected and screwed in the new one. Returned the racks and slid the oven back in.
The only remotely challenging part was disconnecting the old sensor. I had to figure out where to press with the flat screwdriver to get it to release.
I had found a good YouTube video and didn't use the app.
As the 2 screws in the front of the flame spreader didn't screw into anything , and made getting the flame spreader very difficult to remove, once I got the flame spreader out , I did cut off the screws so future install & removal would be easy. I had to hacksaw the screws off , as the screws are otherwise impossible to remove. The screws were damaging the oven metal sheet work during first removal ! Otherwise the new bake ignitor install would have been a very quick 20 minutes. Also I watched u-tube bake ignitor install & oven door remove videos, which were extremely helpful.
Oven would lite once and after that it would just click 3 times and nothing, click 3 times and the same thing!
Removed the bottom pan and heat shield plate, removed the drawer to get to the igniter disconnect the one wire from it and removed it and just repeated the same process backwards to put the new one in. All under 15 mins
REMOVE BOTTOM OVEN PAN. REMOVE GAS DEFLECTOR. REMOVE GAS TUBE. UNPLUG WIRE. REMOVE TOP AND BOTTOM SCREWS ON IGNITER. REPLACE IGNITER AND REATTACH IGNITER SCREWS. RE-INSERT IGNITER PLUG. REPLACE GAS TUBE AND DEFLECTOR. REPLACE OVEN BOTOOM PAN.
Removed grills. Removed bottom plate. Removed flame shield. Removed igniter, 2 hex head screws. Bottom one is a bit awkward. Disconnected wire. Installed new igniter. Careful not to drop stuff in the hole. Like a socket. I did
