MEW5527BAW Maytag Wall Oven - Instructions

Disconnected power pulled oven from wall, removed 8 screws from back, unplugged sensor, removed old, attached new, put screws back wow saved me $500. From buying new and $150. For service call

Followed provided video

Easy peasy.....Turn off the power in the breaker box to the oven. Take the racks out of the oven,remove the two screws in the very back and pull the element out a few inches(don't be afraid, you may have to use a little force). Pull the clips off of the element and remove it. Replace with the new element and reverse the proceedure. I love knowing I found a websight that had what i needed, was easy to navigate, and offered instructions with the part. NICE!

The thermocouple was suspect. It should be super easy- two screws, but the wiring harness would not pull through on my oven. I confirmed the procedure with the PartSelect video which is good. The harness was caught and broke so I had to pull the oven out partially to get to the harness. The sensor did check bad on the multimeter (resistance too high- Google it, I did) so I ordered the part. Once the new part was installed the oven still did not function. So I had to get busy with the multimeter and pull the oven again. On the back of my oven near the wire to the bake element is a Hi Limit Switch which cuts off the bake element if the outside of the oven gets above the preset temperature. Mine was cracked and faulty and had to be replaced. The oven works great now.

take the old ones out and slide the new ones in ordered around 2 in the afternoon and they were delivered to my front door around the same time the next day very pleased with service and the racks. I just wish I could get parts for my Jenn-Air cooktop which is 20 years old maybe somewhere someday.

Remove 2 screws in upper left corner of stove holding sensor in place. Pull sensor out and disconnect plastic electrical connector. Select appropriate adapter (both styles provided with new part) & reinstall. Power up stove and select bake on control unit to test. Works like a charm!

I removed the old thermostat and replaced it with the new one using the supplied wiring adapter for my model of range. Parts Select made this an easy project. Thanksyou

Followed directions as supplied. New part did not work, so it must be in the control unit which is no longer available. So time for a new range.

Very simple, hooked up with two screws...so easy, and ordering was so easy and came in two days!,,

Turned off breaker,opened door with bent coat hanger by sliding right to left the coat hanger to open the door, remover 2 screws holding in the sensor in upper left corner of the oven. Remove the sensor (gently) with the wire connection from back of oven pulling sensor out a out 8 inches . Disconnect plug. Install new sensor with matched harness /.connection, installed 2 screws ,turned on breaker.

I replaced the oven sensor which was easy to replace. A pigtail wire was provided with the sensor which is intended to be installed first so you don't have to reach around the front and back of the oven at the same time. The replacement was easy. However, that turned out not to be the problem. The real problem was the maytag electronic clock control timer, temperature control unit. The part number is 7601P177-60. This device has been discontinued and I was fortunate enough to find the part at a local supplier. Once I replaced this, the problem went away. The oven heats up normally. My original symptom was that when setting the oven temperature to something like 350 degrees, the display would rapidly report heating up the oven to that temperature, and the oven was only mildly warm. If you have that symptom, it is probably not the oven sensor. It is the electronic clock unit. Hope you can find one. If you can't, I think you need to by a new oven. Regards

I watched the video, which was very helpful...the temperature sensor was hard to pull through the small opening in the upper back left oven corner. On the back wall of the oven was a large removable circle, so I unscrewed that piece and was able to gain access to the wires attached to the temperature sensor and push it through the small opening. I used one of the new connectors, pushed it back through the small opening, screwed it back onto the oven wall, replaced the circle opening and tried the oven again...unfortunately, there was no improvement in oven temperature! My JennAir wall oven is about 17 years old, and I thought I would try this $30 repair prior to purchasing a new wall oven, but it looks like I will have to do some overtime and buy a new oven. Any other suggestions would be welcome.

Followed video

I removed the old sensor via the two screws holding it in, unplugged it and replaced it with a new one.

New part delivery was prompt, arrived within 24 hours and was well-packaged. Removal of old element was complicated by one of the two original wires being caught up in the housing behind the oven. After removing the circular metal plate in the back of the oven the offending wire could be accessed and rerouted. Plugging in and installing the new bake element was quite easy and without complications.