Quick Question!

Have you ever purchased from PartSelect.com before?

Models > MDH25YW2

MDH25YW2 Frigidaire Dehumidifier - Overview

Get Parts and Repair Help for MDH25YW2

If you know the dehumidifier repair part you need, you can browse the list of all parts on the MDH25YW2, or you can search by name or part description. You can also find your part by where it is located on the MDH25YW2 by selecting a section below. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$32.65

Compressor Start Relay

The compressor start relay attaches to the compressor in your refrigerator. If your refrigerator will not start, one of the most common parts to fail is the compressor start relay....

Order within the next 3 hrs and your part ships today!
$31.97

Float

If the bucket is full indicator on your dehumidifier is on, but the bucket is empty, or your dehumidifier is overflowing, you may have a problem with the float. This device is located near the bucket and moves up as the water level in the bucket rises. The float will trip the water level switch when the bucket is full. This is a safety device to prevent the unit from overflowing. When the switch is tripped, power to the compressor and fan motor circuits is disrupted until the bucket is emptied. Make sure that the float assembly can move or pivot freely so that it can trigger the level switch when the bucket is full. If the assembly is warped or damaged it should be replaced.

Order within the next 3 hrs and your part ships today!
$25.98

Auto Shut Off Switch

The auto shut off switch is for dehumidifiers. If the water bucket is not attached properly the switch will ensure the compressor does not run. You may need to perform a continuity...

Order within the next 3 hrs and your part ships today!
$6.59

SCREW

Order within the next 3 hrs and your part ships today!
$1.24

STRAP-COVER MTG

KNOB-CONTROL

Water Container Reservoir and Float

$1.08

LENS

This indicator light lens protects bulbs in ranges, ovens, stoves, and humidifiers. The lens keeps the bulb from getting cracked, scratched, and damaged. It is 1 inch long and 1 inch wide. If your lens is defective or broken, or the bulb is easily getting damaged, replacing the lens can be a solution. Refer to the installation instructions provided by the manufacturer for further accurate guidance. Remember to unplug your appliance from the power source before starting this project and wear gloves to ensure your hands are protected.

Order within the next 3 hrs and your part ships today!
$96.49

Humidistat Control

This is a humidistat control for a dehumidifier. The humidistat on your dehumidifier responds to the humidity in the air to determine if the appliance should continue to dehumidify...

Order within the next 3 hrs and your part ships today!

Fan Motor

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Compressor was short cycling

  • Customer: Sherman from Tuttle, OK
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 8 of 12 people found this instruction helpful
Removed the cowling with a square drive screw driver, removed the spring clip from the cover of the compressor controls with a screw driver, pulled off the old compressor start relay and replaced it with the new part. Since other problems could have caused the compressor to short cycle this was a "replace the part and hope it would work" since that would be ... read more

The compressor would not run.

  • Customer: Linda from Gurnee, IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 6 of 10 people found this instruction helpful
I removed the cover, used a multimeter to test the compressor circuit, and found the compressor start relay to be defective.
Ordered a new one and installed it when it arrived. read more

Unit would run continuously and not shut off

  • Customer: Jonathan from New Oxford, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
Removed the front cover and then the humidistat from the bracket. Two push on wire connectors and then reversed. Very straightforward and excellent part matching. Given the prices for new dehumidifiers it was great to breathe life back into this unit which does its job well. Thanks for the easy to use web site and fast fast service! read more