Quick Question!

Have you ever purchased from PartSelect.com before?

Models > MDBTT60AWW > Instructions

MDBTT60AWW Maytag Dishwasher - Instructions

All installation instructions for MDBTT60AWW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MDBTT60AWW
706-720 of 796
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Door latch broke/ wouldn't close properly

  • Customer: Ken from La Habra, CA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Very easy do it yourself. Cut the power off to the dishwasher. Open the dishwasher door. Unscrew the corner screws of the door cover. (About nine screws. You may need to use a nut driver or allen wrench. You can elect to take off the entire cover or leave it on. I had enough room to leave it on. The latch assembly sits on top of the door mount. It comes right out. Use a screwdriver to remove the latch assembly from the two electrical connectors. Be gentle with these connectors. This is where you may need to remove the entire cover, just to give yourself more elbow room to work. Replace the old assembly with the new one. (Note: you have to replace the entire assembly even if just the door latch is broken.) Remount the assembly to the fixed mount, close and screw the cover to the door and your done. I ordered the part on Thursday, received it the next day and installed in less than thirty minutes. And the part was a perfect match.

Dishes and glasses were left with little specks of food on them.

  • Customer: Vaughn from Great Falls, VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
We watched the very excellent video on this web site for replacing the Accumulator Filter and followed the instructions it provided. It's possible that we could have just cleaned our existing accumulator filter once we understood what it was and how to get to it, but the results of replacing it have been dramatic. It's like a new dishwasher.

Food chopper was broken.

  • Customer: Bob from Souderton, PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
Followed video. Everything went together fine, but leaked water around motor shaft seal. Read comments section on video and someone had the same problem. I had pushed the seal into base too deep. I pulled it out and reseated it. It worked without leaking after that. Bob

Dishwasher Did Not Clean And Drain Properly

  • Customer: Noel from Orange, TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Routine repair. There are videos on the net that show exactly how to replace the filter unit. However, when you order the filter, order a replacement pump impeller. The impeller must be removed to remove the filter on this model. The impeller was stuck on the shaft, and I had to destroy it with the side cutter pliers to get it off. Before putting the new one on, clean the pump shaft thoroughly and lube the shaft with silicon lube or vaseline jelly. Clean the bottom of the water pan thoroughly, then reassemble. Then pour one cup of vinegar in the bottom of the dishwasher and run it with no dishes. This will clean the inside of the dishwasher.

The glasses on the top rack had food particles in them after a wash cycle

  • Customer: David from ocala, FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I initially took everything out and cleaned everything with the shop vac, and outside with the garden hose. That did not work, so I looked on parts select for a new accumulator filter, as I was not able to clean that very well. To install the new filter, I removed the sliding racks, top and bottom, and the water manifold, then removed the lower wash arm, then the parts under that, the filter plate, the outlet, the impeller, all the way to the accumulator filter. After removing that, installation was the reverse. I also cleaned the middle washing arm, and the lower, as I noticed food particles blocking the outer holes. All is good now, and the dishwasher, which we use almost every day, is working fine.

Dishwasher would not move through the normal cycles

  • Customer: James from Salisbury, NC
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Removed all phillips screws inside door panel and separated panel form door enough to access the control board. No need to disconnect the wiring harness except where it connects to the control board. Used nut driver to remove screws holding the control panel to the door. Gently tugged the various circuit bundles to remove each from panel except the ribbon circuit in the very first position, this is secured by slide/clamp which should be slid outward with fingertips, ribbon connector will then easily disengage. To install new panel simply reverse the removal process being especially careful to insert the ribbon circuit all the way into the slot before reengaging the slide/clamp. Secure the control panel to the door and then reattach the cover -. Good Luck.

Mice living behind the dishwasher

  • Customer: julie from golden, CO
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Mice were living behind and on top of the dishwasher and destroyed the pad. Had to throw it away. Ordering you was easy, and the pad fit perfectly.

door wasn't latching and started its cycle before door was shut

  • Customer: Randall V from Loveland, OH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I just followed another persons directions that was in the system already. He had a great idea by taking the new switches out of the new latch and replacing them with the old ones from the bad latch. The old switches are still good and it made for a simple repair. This way you didn't have to disconnect the wire from the switches and now you have two new switches on hand. The old switch had a burnt spot on the connector.

The dishwasher door latch was broken and would not hold the door closed.

  • Customer: Ruth from Canyon Lake, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I unplugged the dishwasher under the sink. I opened the dishwasher up and took out the 12 screws holding the inside door facing on. I gently moved the door facing down towards the dishwasher to reveal the door locking mechanism at the top of the door. I unplugged the mechanism and plugged in the new one. I put the door back together the same way I had taken it apart. In all it took about 12 minutes. Works like a charm.

broken door latch

  • Customer: Donald from St. Pete Beach, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed door frame screws. Pulled front panel from frame. Removed white plug,than removed black plug. Switch was tnan loose removed and replaced with new. Pushed door together and replced screws. Successful repair. Thank You!

latch handle on dishwasher was broken

  • Customer: Loren from Fulda, MN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I used a screwdriver with a torque bit and took off the inner door panel. Move the panel to the right side (as you face the dishwasher). Disconnect the two wire connnectors with a needle nose plier and discard the handle and connections. Install the new latch by making sure you attach the wires to the proper connectors. Make sure the connectors 'snap' in place. Place handle in proper slot and replace the inner door panel making sure that the two small flaps on the bottom of the inner door panel go inside the dishwasher (they cover the hinges). Tighten the screws and you are done!

door latch handle broken

  • Customer: robert from phoenix, AZ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
removed door liner , removed door latch. switch has two spade type electric connectors you have to remove.place new latch handle in place, connect spade connectors , replace door liner. dont forget to turn power off. very easy job

Worsher door latch broke at top of conction .

  • Customer: Robert from Indianapolis, IN
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I took out the screws that heald the door togeather and the handle was releasted..I tryed to repair it but could'ent. I looked PartSelect up on the computer and found the part I needed and ordered it. It came in 2 days and I instaled it. There were two electrical wires to conect on each side and then I screwed the door back togeather and it workes fine now. I am very satisfied...Thanks

the handle of the dishwasher broke

  • Customer: Maria from East Setauket, NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
I followed the instructions given, and also viewed a video of the repair on YouTube. The hardest part was to figure out which circuit was for the dishwasher! I can't believe I solved the problem for less than $40.00 and in time for Holiday entertaining! Thank you!

Handle to door latch assembly broken

  • Customer: Stephen from North Lewisburg, OH
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
After waiting for FedEx to finally deliver the part which they held at their warehouse for almost a week. I just shut off the breaker to the dishwasher, safety first, took out the 11 strews holding the inner door panel in place. Then I lifted out the old assembly pulled off the connectors. Then I slid the connectors onto the new assembly put the assembly in place and installed the screws and the job was done. The only tricky part was that it took some effort to pull the connectors off the old part.
All Instructions for the MDBTT60AWW
706-720 of 796