MDB8951BWQ10 Maytag Dishwasher - Instructions

FIrst I went to your web site; located the part on the easy to read diagram. Next I ordered the part. When the part came to the house (2-3 days), I opened the box and then the packaging, I screwed the part in and Wala! Boom! Bang! She was fixed!

All kidding aside. The part order was quick to locate, quick to ship and one of the easiest companies to deal with. I will return on my next dyi project.

Maytag should be ashamed to put such poor plastic material in an otherwise good design. The seals that join the rotary sprayers to the rear wall had hardened and crumbled away. When I discovered that water pressure had been lost at the spray arms, it was a simple fix. Snap off the failed parts, pay Partselect $37 because Maytag wanted to save a dime and snap in the new parts. (Parts that will fail again in another 3 years.)

First, I removed the screw, then I took off the old wash arm, then I replaced the wash arm, and replaced the screw. Nothing could be easier!

I thought the door springs were broken so I ordered both springs and cables. After the parts arrived I removed the six screws that hold the dishwasher in place and slid the dishwasher out about five inches. Neither of the springs were broken but one of the cables was broken. I changed both cables, slid the dishwasher back in place and replaced the screws. The whole job took about 20 minutes. It was a very easy job.

Removed screws holding the dishwasher on the side of the cabinet.
Removed the screws from the bottom plate of the dishwasher.
Pulled out the Dishwasher from under the cabinet about 1 foot .
Removed broken Spring from left side of bottom holder making sure not to drop the plastic swivel arm from the bottom metal bracket.
Put the new spring, short loop side end in the plastic swivel arm and expand the long side spring end to the upper bracket holder. Their are 4 different tension slots depending upon how tight you want the front door to open or close. I put the spring on the 2nd slot
Put dishwasher back under the counter, screwed bottom plate & side in.

I followed the you tube video exactly. Very easy to do. I did not tighten the screws sequentially as shown in the video, rather I did the opposite ones to make sure nothing was skewed. Very easy, about 20 minutes.

I bought 2 new new door springs and just replaced both left and right. Just have to pull out the dishwasher about 1/3 to its original position to be able to fully open the door and replace springs located on the side. This model is not complicated . Its very easy to replace parts that are broken. Don't forget to TURN OFF your CIRCUIT BREAKER

Unfortunately, my experience was unlike that of the other people who posted. While everything did go back together it was very difficult to get it all to press down tightly enough to tighten each set of screws. The project took about 2.5 hrs and I still don't think it is exactly right. I'm still going to have a professional out to finish the job. Also, the tool needed to complete the job was nothing fancy, but also not in everyone's home tool kit.

Very easy after watching the video. thanks

received new basket without a basket handle; had to remove handle from old basket & attach it to new basket; took 2 separate tries to remove old handle & each try took about an hour; used screwdriver & pliers but had to be careful not to break handle; eventually used dimes to pry open & hold the attached sections of the handle open in order to free the handle from the old basket; we sure hope the new basket lasts a lot longer than the 2 years that the old basket lasted before it broke.

You just remove the old unit and set in the new unit. the wheels were already connected.

replaced rack

Ordered part. (Part was larger than the original . That is it dis not fir int supports tha same as rhe original. Hut i modifird the support by assin copper wire to fanten the heater to the supports.) The instalation was no pronlem with a little engineering. Works like a charm, Wife Happy Most important result.
Elmer

remomed old adjuster and attached the new one to the housing and it was done it was very simple

I removed the main plastic bolt with a pliers and then just used a screwgun with a star tip for all the screws.
I am a 43 year old woman with no experience and I was able to figure it out. The machine cleans much better now.