MDB8600AWB Maytag Dishwasher - Instructions

Unplugged electricity to dishwasher,unscrewed the interior cover, pulled out the handle and latch assembly, had some difficulty unplugging the electrical connections(best to insert a regular screwdriver tip in between and twist), removed the assembly, then plugged in the new assembly noting to remember which wires go to which side, and then reattaching the interior cover, plug back in the electricity. Really simple fix. PS: The 2nd time this has happened, the first time under warranty with maint. man doing the work.

removed the hex screws from the door and unplug-ed the two wire connections from the handle which took the longest part of the job and replaced them on the new switch put the screws back in the door and the job was finished a job anyone could do. calling part select was so easy and got the right part the first time was just what I needed to make this an easy as pie job. part was shipped on a Friday and had the part Saturday afternoon. could not ask for better service
Thanks

Just like all the other forums state, the old one comes out easy and the new one goes on just as easy and works perfectly. No issues or hiccups. I did do it a little differently though. I pulled off the two switches on either side of the new and old handle and put the already wired (old) switches on the new handle. Made the job easier in my opinion and hey, it wasn’t the switches that were broken just the handle, so no need to replace them.

I just replaced the purchased rack stoppers with the broken ones.

Turned power off to dishwasher. Removed eleven screws holding the inside liner of the dishwasher. Raised liner, latch assembly right at hand. Disconnected wiring from old latch, connected wiring to new latch, dropped liner back in place. Two of the liner screws also hold the latch in place. The hardest part was taking the eleven screws out of the liner

pulled broken piece off and snapped new one on.

I removed the screws holding the inside door panel on and lifted the top end of the panel. Then I disconnected the two switch wires attached to the latch assembly. Reconnected the wires to the new assembly set the latch assembly in place lowered the panel back down and replaced the screws. Piece O'cake.

Fairly easy repair, once I had the right tools. Unplug the old latch and plug in the new. Re-set the screws and done.

I just took off the four screws and put the entire roller adjuster on was done in less than 5 minutes

I removed the screws holding the front of the door to the inner door. I un-snapped the two electrical connectors and snapped them on the new part. I fit the new latch mechanism to the door front and screwed the inner and outer doors together. The other stories that were posted were a big help. It could not have been simpler. I was surprised and impressed at the web site and how easy and fast it was to obtain the correct part and fix it myself.

I removed all the screws holding the inside panel to the door. Two of the screws held the Door Latch Assembly in place. Once I got the new Assembly, I removed the wires connected to the old one and attached the wires to the new one, paying attention to which one connected to which side. I screwed all the screws in and tested the dishwasher and everything worked fine. Easiest repair I've ever done.

I am not an appliance repairman but I will try anything once. If I break it or screw something up, who cares. It was already broken right? This was a simple and easy repair. Removed the torx head screws. Lifted the inside door assembly. Propped it up with a wooden block. This allowed me to remove the old handle and door latch without having to remove any wiring except for the door switches built into the replacement assembly. Marked the lower wire on each of the wiring connectors attached to the switches. This saved me worrying about whether or not I had the connector the correct way. Lifted the old handle and door latch out. Removed the connectors using pliers. Try gently rocking them back and forth to avoid breaking the switches as they can be reused if they are still good. Plugged the connectors into the new switches and dropped the handle and door latch in place. Removed the wooden block and set the inner door back in place. Note: 2 screws that hold the inner door in place also hold the handle and door latch. Replaced the screws and ran a load of dishes. All together it took me less than 10 minutes to replace the handle and door latch.

First, I removed the screws holding the inter liner to expose the broken part. I then removed the handle assemble, the broken part. I then got on the internet and serached for a parts place replacement company and I found Parts Select. I entered my request and purchased the replacement part within minutes. The part arrived in a couple of days and I installed it without a problem. Great service!

I first disconnected the power to the dishwasher. Then opened the door and removed the 11 hex bit screws holding the back onto the door.The latch assembly with the handle is held in place with 2 of the back screws already removed. I unplugged the 2 plugs on the old latch assembly and reinstalled the new one in reverse order. Very easy job just make sure you don't reverse the plugs. Remove and reinstall them one at a time. The new latch assembly is very good quality and even comes with new switches.

removerd six screws, removed inside of door, removed handle latch, slid off two wire conectors. reinstallede wires slid latch into door amd replaced screws. Door works perfectly now. Very easy installation and the part was delivered in two days of placing order.