LSD2615HEZ Admiral Refrigerator - Instructions

I removed contents of freezer as this was a bottom unit. I had to remove freezer drawers/door to easily access ice maker which was located in the back of unit,wasnt a problem.I did however take a hair dryer to water tube as it froze up with about an 6 inch tube of ice that finally slid down. Connected unit and had ice within an hour or so and a full tray within 24 hrs. Second ice maker in little over a year...Video very helpful, saved 100 bucks by doing myself. Part arrived fast, great job!

We ordered a PartSelect PS2121513 ice maker. I was concerned that there was no instructions shipped with the unit. Fortunately, PartSelect had an online video that guided me through the process. It wasn't that complex really. The only time I felt totally dumb was when using my nut driver to remove the bottom bracket. I couldn't figure out why there was no 1/4" socket with my set, so I used a small socket wrench instead. I finally figured out that the driver was already a 1/4", without a socket in it. After that it was easy. Slid the ice maker up a little to free it from the top mounting screws. Pulled it outward a bit to gain access to the connector at the back of the freezer, then squeezed the two sides of the connector and out it came. I popped the plastic cover off the existing device and then removed the connector as instructed in the video. I also removed the bale (as per the video). I put the connector harness, plastic cover and bale on the new ice maker and put it back in, this time using the nut driver on the bottom bracket :-). My only concern after that was that it didn't seem to be working. I had no idea that it needed some time to get cold before it would work. After about an hour, it filled with water and began making ice. Success.

Removed bucket,and removed the front cover. the ice wheel was removed by removing the nut from the blade assembly and removing the blades washers and spacers. The parts were replaced in reverse order and the nut replaced. The ice maker was removed by removing the bottom bolt, loosening the two side bolts and lifting the unit off the bolts. the cover was removed from the ice maker and the tab depressed on the wiring harness which was then unplugged. The wire was removed and replaced on the new unit the harness plugged into the new unit and cover replaced. The unit was the placed back on the bolts, tightened and the bottom bolt replaced. the ice bucket was replaced and unit turned on. Ice making within an hour.

turned off the water supply,disconnected the power from icemaker to the back wall,loosened the two screws on the top,and one screw on the bottom.removed old icemaker.took the bale off,to put on the new icemaker.removed the wire harness from the old,to put on the new icemaker..saved over $200 for the repairman,had a full tray of ice in 6 hours.(watching the video,helped)!!!!!,very thankful for your service,as most of my appliances are all in that ten year period,i will be ordering more as needed.

Empty out freezer loosen two top screws and took out bottom screw. Lifted out ice maker and unplugged wire. Took bailing arm and plug and put on new ice maker and reverse the process. Had ice in three hours and no leaks.

The repair was simple. It was a matter of unpluging the old relay and then pluging in the new one. I almost bought a new refrigerator but after doing alittle reading on this web sight and finding out the most common reason for having the problem I was having I decided to order the relay. It was the problem...$ 70.00 -v- $1400.00. I'm HAPPY !

Removed wiring from old ice maker and install on new. With 2 screws all ready in place hung ice maker on them. Attach wire connector into socket and install bottom screw to hold ice maker. Tighten top 2 screw and put wire guide in place. Drop wire guide down and ice started in 10 mins

The icemaker in my Maytag refrigerator was having a few problems. First, a small leak developed in the ice cube tray, allowing water to drip into the ice bucket. This of course caused the ice to become one solid mass, totally inappropriate for a gin and tonic. After a couple of months of this, it stopped working altogether. On to the internet I went, and discovered how easy this repair actually was. One nut to remove, one to put it back in. The installation video was very helpful. I did have a concern at first because the icemaker did not start making ice rights away. I thought it might be a defective unit. It took about 12 hours to get the first batch and it has been happily cranking out the ice since! Ed in upstate New York.

Exactly like the instructions in this website. Unplug the refrigerator, remove 2 screws from the door ice/water dispenser, remove cables from solenoid, remove ice chute Seal, ice chute door insulation, ice chute door, remove hinge-door and spring, replace in reverse order and in 15 minutes the problem was solved.

I took the glass off the old shelf. I then removed the crisper tray following the old crisper shelf. I put hte new shelf in, which fit perfectly, and replaced the glass and tray. It was super painless and took no time at all....all within 5 mins.

Followed the video as a guideline. It was not exactly as portrayed. My husband and I, being long time do it yourselfer's, were able to get around the differences. There were screws, instead of tabs as pictured in the video, plus had to remove 4 screws instead of one to loosen the old icemaker. After 2 days the icemaker is pumping out loads of ice.

Ordered the new parts, and they arrieved while the wife was away. I removed old ice maker and install new one in about 5 mins. as you really only have to remove 1 nut and unplug. New one fit like a glove. Ice bucket wa broke where it slides into the track. Remove 4 1/4 net screws, installed ice tray feed auger into new tray and installed it back into the frig. Had ice after about 1-2 hours. Parts were pricy but they were exact fits. Parts came in early also.

I performed the replacement just as the video instructed. Very simple repair.

Looked at questions, picked one that applied, ordered suggested part, fix was super easy after watching video, Frig in running, part fixed it. Very excited, Thankyou.

Unscrewed the old filter and screwed in the new one