LRSC21934TT LG Refrigerator - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Water/ice maker not working
Remove push plate for water/ice maker switch, remove 2 screws and 2 wires for switch. Replace with new.
Parts Used:
-
Brent from ROGERS, MN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
6 of 17 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replace the light switch for the refrigerator
Cover the putty knife with tape so you do not scratch the side wall where the switch is located. Slide the knife under the edge of the switch and push in a bit towards the switch and slightly twist to pop the switch out of its hole. Disconnect the wires from the switch and simply plug in the new switch. Push wiring back into the hole and careful push the switch into the hole until it snaps into place.
Parts Used:
-
Karyn from DURHAM, NH
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Refrigerator light had a short in it and would randomly work
Unplugged the fridge. Used a screwdriver to loosen the switch. Easy to disconnect from fridge and just plugged the new switch in. Popped right back into the side of the fridge and worked perfectly.
Parts Used:
-
Tammy from HAGERSTOWN, MD
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
1 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The ice maker door stay open. And not close back.
-
Toai from Monroe, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
light out
-
Jack from Ellenton, FL
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Recommended change interval for water filter.
-
Willard from COMPTON, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
1 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Threads were striped on water valve leaked needed new one
Shut water valve off drained water in refrigerator instAlled new valve
Parts Used:
-
Nicholas from Melborne, FL
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Wrench set
Was this instruction helpful to you?
Thank you for voting!
Ice cubes did not drop out of tray when the ice maker cycled
1) Take out 3 screws from top of icemaker. 2) Unplug electrical connector from wiring harness. 3) Remove icemaker unit from freezer and then remove frozen cube sensor with clip and rear insulation. 4) With your hands pull cube tray motor out of the holding clips with the tray- if this is too difficult, spread bracket and only remove the tray from the unit. 5) Insert new tray into slots and install new or existing ice sensor, insulation, and sensor clip. 6) Reinstall icemaker unit to ceiling of freezer, don't forget to plug into wiring harness. 7) Turn unit on and make some ice!
Parts Used:
-
Michael from Eagle, WI
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Each time we've had to move we have to remove the doors from the fridge to get it thru the front door.since water and ice run thru the freezer door there are 2 tubes that connect at the bottom of the freezer door that aren't meant to be separated very often if ever.it's easier to cut the tubing on b
With alot of elbow grease and a pair of pliars we managed to get the old connector off wo cuttig the tubing as the tubing was getting to short from being cut once to many times & there was no more play in the length.Original connector was a different color and shapped slightly different than the new one so was a bit concerned that I had ordered the wrong part but it went one very easily & did not leak. We even managed to remove it again just to see if it was possible wo cutting again. it came off with no trouble.I would say the replacement part was a better fit than the original simply because we could remove it easily wo having to cut the tube!
Parts Used:
-
Sarah from Elk Grove, CA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers
Was this instruction helpful to you?
Thank you for voting!
Ice tray was bent and spilling water onto ice making it freeze
I took the ice out with one screw and took out the old tray the new one slipped right in and I hooked up the little heat strip with one snap works perfect cost $10 I was told by appliance repair tech that I needed to replace the ice maker for $450 saved $440 dollars replacing the bent or warped ice tray
Parts Used:
-
William from Nolensville, TN
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!