LRM1250W 01 (LRM1250W/01) LG Microwave - Instructions

Easy, and the microwave still doesn't work.

i unplugged the unit,unscrewed the outer shell so that all the wiring and internal components were visible.starting at the first of three micro switches i removed the slip on terminals installed the alligator clips too the wires so the switch would now be bypassed.i made sure the wires and clips were not touching anything plugged unit in and it worked.i then installed the new switch and closed up the outer shell

I UNPLUGGED the microwave and removed the cover, using a phillips and a Torx screwdriver for the machine screws. I set these screws aside, so as not to confuse them with the later encountered screws. I photographed the magnetron to assure proper placement of the 6 phillips machine screws involved in reassembly (marking the the locations on the old magnetron would do as well. I marked the old magnetron "old", to avoid later confusion. I removed the two screws holding the shields to the magnetron. I removed 3 of the 4 screws holding the magnetron to the microwave, leaving one of the top screws. I held the magnetron securely and removed the last screw, pulling out a the part of the magnetron that penetrated the microwave. I installed the new magnetron in reverse order. One problem I encountered was locating one of the six screws, which had been pulled into the old magnetron by magnetism.

Take off cover then the bottom. Transformer is on the bottom plate and wires won't let it come all the way off, too many wires to pull off so will have to position the bottom plate so you can get to the motor. Remove 1 screw on motor and remove motor. Install new motor connect wires replace bottom plate, replace cover. All done (hope & pray it works ok) mine worked perfect. Hope this helps.

Initial failure of over range microwave Aug 3rd. Control Panel worked but no heat. Took to local LG authoriaed local repair place. They fixed it quickly and we re-installed it. Worked fine for 2 months then had similar failure again. Agaim took to same authorized repairer. They kept unit for 3 months but finally concluded theu could not fix it and suggested we contact LG for a partial refund. When they tested the unit during re-assembly in my presence, there was a blue flash and the fuse blew. Since we had built a custom tile mural back splash around this unit, I brought it home, ordered a number of time delay fuses new capacitor and two new high voltage diodes. However, using my Fluke DMM, I checked the existing capacitor and high voltage diode and they checked OK so I just replaced the time delay fuse. The high voltage transformer leads had 2 possible ways to connect to capacitor and diode. Tried one way, plugged unit in and turned it on, and immediatly blew the fuse. Replaced the fuse and reversed the high voltage transformer connections,amd turned unit pn, and it worked perfectly. Since we had experienced several power failures during the time of the original failure, the repairer concluded that power spikes might be at fault, so I also purchased a TrippLite ISOBAR4ULTRA 3300 Joule surge protector between wall outlet and microwave, and re-installed over range. It has worked perfectly since.

Ordered the switches from Partselect, arrive in two days. Had trouble removing the plastic connectors from the old switch terminals, one of the plastic protectors broke, but was able to reuse it. It took a little figuring out how to remove the existing switches. Must push in a tab and rotate the switch on a little pin, then remove. Must be careful not to break the plastic tabs holding the switches in place. Replaced all (3) switches at the same time. All in all it was pretty easy.

I tested the motor with an OHM meter, saw it was shot. Broke the turntable off when I tried to take it out from inside where it's attatched to the drive motor.( The plastic was like glued or welded onto the shaft of the original motor ) Had to open up the removable trap door on the bottom to pull the one screw that holds the motor in. Swapped it out, pushed the new turntable back in, and turned it on. Works like new! great parts, fast shipping, great deal !

Overall repair quite simple. Removed screws from the sides and rear of the microwave, then removed cover. Next, removed only the screws to separate the bottom cover. Removed the one screw in the AC Synchronous motor to remove the motor (had to use small screwdriver through a vent slot in the bottom to remove the screw). Unplugged and removed motor. Installation is the reverse of removal. Note: on the back of my appliance were 4 torx screws with a tamperproof pin in the center. I used the rotary tool to grind out the pins so I could use a regular torx bit instead of ordering specialty bits.

Lifted up the glass plate, lifted out the plastic base that rotates and placed the new one inside. The piece that connects is shaped like a semi-circle, so I rotated it until is dropped into place. Then I put back the glass plate and it was finished.

Put on safety glasses AND leather work gloves. Grab pliers. FIRMLY grasp the110 A/C power cord with jaws of pliers, squeeze and pull plug from 3prong power socket. Carefully press black bar on front panel to open oven door. Stand back so door doesn't strike your face . Lift out damaged glass tray with BOTH gloved hands..place in re-cycle bin. Open parts package carefully and install the NEW glass tray. Plug 3prong plug BACK into 110v outlet and press start button........Stand back! View the new glass tray turning in a circular fashion through the heat/radiation proof front door. Job well done!

Eight screws off the bottom exposed the cover plate. Easily found the motor location the looked up the item number and verified data and ordered the part. Replaced the motor, tightened the screws and flipped it upright. Plugged it in and the lights came on. Set a time pushed start and smiled! The eagle had landed!!!!

The old button fell out because the "tabs" on the end of the posts that come out from the button had broken off. These "Tabs/posts" hold it in place - you'll see how when you look at it. All that was necessary was to put the springs from the old one onto the new one. Make sure to put the thing in right-side up; there are two "tabs/posts" on the top side, and one on the bottom. Gently slide it into position as nearly straight as you can, squeezing the "posts" until they clear the front of the opening. Continue to slide in EVENLY until you feel the part "click" into place. That's it! I recommend cleaning out the area fully before installation, with a a god household cleaner, and also putting a thin coat of some sort of lubricant on the part before you put it in. (You won't be able to do that after it's installed.)

I removed the outer cover of the microwave and removed the bottom palte to access the small motor. i unplugged the old motor from teh wiring connector, removed (1) screw and motor came out. I reversed the proceedure with the new motor and it was finished.It was a piece of cake.

brought new one and the help with the sites pictures to describe what I need was extremely helpful. The prompt delivery was great.

Unplug.Take off the external cowling from the back of the unit by removing the torx security screws. Tip: instead use a thin screwdriver blade to unscrew the torx screws, or knock out the center pins of these screws. Remove the bottom panel. The replacement motor is attached with one phillips screw, re-attach wires to motor - polarity doesn't matter. Re-assemble and you're finished.