Models > LNC6762A77 > Instructions

LNC6762A77 Admiral Washer - Instructions

All installation instructions for LNC6762A77 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the LNC6762A77
211-221 of 221
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The washer making a ticking sound while in the washing and spinning mode.

  • Customer: Rudy from Yukon OK
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I found the instructions on www.ehow.com about how to remove the shell of the washer so I could find what was going on with the washer and why it would smell like burning metal. I found it was the Drain Pump with Pulley Assembly P/N: PS2347187. It was easy to replace and saved $$$$ from having to purchase a new washer or call a repairman or women.

wASHER WOULD NOT AGITATE.

  • Customer: Ernest from Pasadena CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
pURSUANT TO THE VIDEO PROVIDED BY PARTSELECT, I DISCONNECTED POWER CORD, HOT AND COLD WATER HOSES. ALSO, REMOVED DRAIN HOSE FROM DRAIN PIPE CONNECTION. LAY THE WASHER ON ITS SIDE REMOVED THE PULLEY BELT THEN FOLLOWED THE VIDEO TO REMOVE DUST COVER, C-CLIP, CAM, PULLEY, THRUST BEARING ALONG WITH ASSOCIATED WASHERS FROM THE TRANSMISSION SHAFT.INSTALLATION WAS THE REVERSE AS SHOWN IN THE INSTRUCKIONS PROVIDED IN THE KIT.

machine moved and shook when in spin

  • Customer: virginia from central city KY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
we followed the video instruction that was given,on how too replace the part of the snugger. it worked really well. we are pleased with everything.

washer shook uncontrollably during spin cycle

  • Customer: Adam from Plainfield IN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the video but didn't remove the motor. Instead I lifted the tub through the top. I also didn't have longer screws with that thread, so I used slightly smaller diameter screws with nuts on the end and it worked great.

Pad missing from both front legs which made washer dance around the room

  • Customer: Michael from DeSoto TX
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Easy as pie but had to cut one with hack saw to remove as it would not unscrew. Rust was the problem. Hack saw was the cure. Otherwise repair would have taken 5 minutes Washer now works as it did as a new appliance.

Washer was making a banging noise and not spinning properly and emptying the tub.

  • Customer: John C. from Estill Springs TN
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Socket set
  • 0 of 0 people found this instruction helpful
I replaced the brake spring(not really necessary) and the snubber ring.I also installed a new thrust bearing kit,but the problem turned out to be a bad transmission.I found a good working used one at a local junk yard and so far it is working great.Your how to videos were very helpful in getting the job done properly.Thanks very much!

Screaming noise from under unit. Belt shot from under it :) No harm.

  • Customer: Louis from Goodyear AZ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Used Putty Knife to release a tab on left split of cover/lid assembly lifting up slightly to release the tab, then I repeated the same on the right side. With the belt already flung off of the unit, I saw the 2 screws inside left/right top corners holding the front cover On. I tilted it forward and up and released from two clips on the bottom of the unit. With the front cover removed I saw the pump on the lower right side of the tank. 3 screws and 2 hoses hold the pump in place. Once pump was removed reversed how it was taken apart.

Machine was noisy and slow @ spin cycle

  • Customer: Steve from McHenry IL
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Took apart liked shown in diagram. Re-assembled in reverse order. Destroyed tub seal on disassemble. Also had to cut spanner off with sawzall as it was corroded badly. On the transmission pulley bearing kit. I had to file the pulley shaft down in order to get the correct adjustment for brake release. Took me awhile to figure that out as there was no way the jesus clip was going back on with either washer. Once filed went right together and using the thin washer I was still at the min adjustment.

Shaking, bouncing, banging, during the spin cycle

  • Customer: Shad from Clearfield UT
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I followed the directions online, but they don't talk about two difficulties with this model. The first is removing the drive belt. This is CRUCIAL! Tilt the dryer backwards, and remove the belt from the pulleys. When putting it back on, when the repair is complete put it on the two smaller pulleys first, and then the large pulley. The other difficulty that is not addressed with this model is accessing the suspension springs. If you choose not to remove the entire housing, I would use a wooden block (2x4 works great) to act as a lever for the vicegrips. I may be weak, but I have a bruised forearm that would have been avoided if I had thought of the wooden block earlier.

Water pump leaking water

  • Customer: Eloy from Andrews TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 0 of 0 people found this instruction helpful
Watch video, fallowed it's instructions which made it a "piece of cake"

Washer bangs while in the spin cycle

  • Customer: Eugene from Bergen NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I removed the belt and pully form under the washer. Lefted the top cover, removed the hardware above the tub, took the front cover panel off to gain access to the tub. Used pliers to remove the springs. Lifted the tub up high enough to install the snubber ring. After putting tht washer back together and doing the first the load the washer stopped banging.
All Instructions for the LNC6762A77
211-221 of 221