LG2912 (P7804818W W) Amana Dryer - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
I have a Maytag gas dryer, it runs but it dud'nt get hot....
First I opened the back panel & check the fuse with multi meter tool ( put in ohms & set it in 200K) & the fuse is Ok, try to run the dryer while looking in the flame dock & the burner starts & had a fire till about 2-3 mins. & flame comes off, what I did is I open the front door to access into the gas burner, check gas valve coils with multi meter tool for continuity & found out that one of the coil doesn't have continuity. I ordered a pair of coil that is located on top of the gas valve on this site & unexpectedly it came in the next day, WOW! that's a fast delivery I was very pleased w/ the service, come home from work & installed it right away & it took me 5-10 mins. Put back everything & try to run it & it works properly. So happy with & my wife as we'll, thanks for the great fast delivery.
Parts Used:
-
Darwin from Meriden, CT
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
dryer was making a real loud grinding noise, like nails on a chalk board.
Really easy popped the lid with a flat head screwdriver, then marked wires for door light and switch, took 2 5/16 bolts to remove front door, then 4 bolts also 5/16 to remove front panel but be care ful and remove drum belt then take panel and drum out. Then took a set of ring pliers to remove wheel slapped new one on.then reverse sreps to assemble.
Parts Used:
-
mike from minooka, IL
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
No heat just tumble
Opened the bottom panel w/ 1/4 nut driver to access the flame sensor and easy fix.
Parts Used:
-
Mario from SAN DIEGO, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Horrible Sqweeling
When I first heard it sqweeling I tokk off bottom cover and peeked around the turned it on and it seemed to be coming from a back roller,I sprayed a little wd-40 and it went away,for a day ! Then I found parts select on line and found the problem. The belt had worn into the roller almost to the shaft. I ordered the roller and belt and watched the very helpful video and it took about 15 minutes!parts $29. 00 Piece and quiet without calling service guy priceless !! Thanks steven l. I. Ny
Parts Used:
-
steven from islip, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
broken door latch, door did not stay closed
Saved a lot of time by just using needle nose pliers to break the receiving end of latch off of the front of the dryer. No big deal if parts fall Inside, won't hurt anything. Then just pressed new part into front of dryer. No need to remove front dryer panel.latch piece on door was not broken so I left it alone. Took all of about 2 minutes.
Parts Used:
-
keith from Brookhaven, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
Was this instruction helpful to you?
Thank you for voting!
The dryer door latch had broken.
The older latch was removed and the new one was inserted in to the same opening. It was great! We had the new latch within a couple of days after ordering the part. This worked out really well. Thanks!!
Parts Used:
-
Nancy from Knapp, WI
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!