Models > LER6620PQ0 > Instructions

LER6620PQ0 Whirlpool Dryer - Instructions

All installation instructions for LER6620PQ0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the LER6620PQ0
1,726-1,740 of 1,847
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dryer belt broken

  • Customer: Ramon from El paso TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Let me put it to you this way I called the repair man and they would Charge me $150 to get the dryer fixed,by ordering the parts I spent $32 and 15 minutes installing it with the instruction video very easy to do Take the advice it yourself and save yourself some money $$$ With The extra cash I took my wife out for dinner Now that's money well spent...

Broken belt, worn wheel bearings and idler bearing

  • Customer: Michael R from Ridley Park PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed plug. Removed lint pipe. Unscrewed lint trap under top opening. Popped the top up. Used nutdriver to remove top 2 screws of front panel. Lifted front panel and set aside. Lifted drum out. Replaced wheels and idler assembly. Parts were well engineered and fit perfectly. Vacuumed entire interior. Placed belt around basket. Replaced basket. Slipped belt thru idler pully and onto motor pulley. Tested basket one full turn to make sure the seal was in place all the way around the back. Slipped front onto two bottom brackets. Replaced screws in front with nutdriver. Dropped top back in place. Pushed down into holders. Screwed lint trap back in place. Replaced plug and tested. Replaced lint pipe. Done!

Dryer was not rotating

  • Customer: Daniel from Lynchburg VA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Went on YouTube ,saw a video on how to diagnose and disassemble the dryer. Surprised how easy it was. I figured an appliance repairman would charge 100-150 so I would be wasting anything if I tried it myself.

Dryer would not run

  • Customer: Joe from Harrisburg PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Motor was tight, very hard to turn by hand. take the back motor mount strap off and you will be able to put an adjustable wrench on the shaft of the blower. you should be able to put vice grips on the pulley end and turn motor counter clock wise (CCW) to let handle of vice grips rest against the bottom of the machine and turn adjustable wrench CCW to turn off blower wheel. However, the one I did, the wheel was so tight I ended up having to break the blower wheel down small enough so I could pull the motor out. remove the front motor mount strap and pull the motor out. Install the new motor wheel and motor in the revers order. Set motor in place, install front motor mount strap, put blower wheel in from the back of the machine and start treading on the motor shaft. Then,from the front, tighten the blower with wrenches turning clock wise and put machine back together. Always unplug machine whenever working on it. If you go to Whirlpool web site there is a step by step video that will walk you through this entire process.

blower wheel cracked and broke

  • Customer: Kellie from Norton MA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
i took the back apart to find the problem, then i went online to findout how tomremove the blower wheel, just googled it. Easy!Took itnall apart, just had a bit of trouble getting the wheel off, was on there very very tight. Ordered it through you, easy, and very very quick, received it in a day. I got an email explaining the reassembly process. Easy. Just follow it to a t and you will be fine. As a woman, this was an easy fix.

I had to spin drum for dryer to start, bad start winding on motor, not sure if the problem could have been fixed by replacing the motor contactor. I could not find a part # for just the contactor.

  • Customer: Dale from Joanna SC
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
You have to disassemble the dryer. I looked up how to on youtube.com. I am grateful that people take the time to record the steps in which to do just about anything. Disassembled and ordered motor and fan, damaged fan taking it off, got it in in just a couple of days, installed motor, fan and drum, tested before complete assembly. Works great. Thanks

dryer stop running.

  • Customer: Sophia from Farmington NM
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
My son worked on the dryer it was easy for him he just followed the instruct that came with the order. My dryer is like new now and didn't to buy a new one way cheaper save me a lot of money. Thank you.

Broken Blower Wheel

  • Customer: James from Mosca CO
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Remove the back panel, then remove the housing around the blower, just slide the housing of to the side, you don't have to take it completly of the machine. Remove the top, and remove the front until you can get to the blower motor. Cut the blower wheel plastic down to the metal nut with a fine blade in a recipricating saw, used a bi-directional broken stud remover socket on the nut that was at the center of the blower wheel and large slip joint plyer on the other end of the shaft. Replace the wheel and put back together. It took about as much time to gather up the tools as it did to fix it.,

Roller hub ID severely worn.

  • Customer: Walter from Moncks Corner SC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed top and front of dryer. Removed drum. Removed old rollers from spindles. Installed new rollers and new retainer triangles. Replaced drum. Re-installed front and top.

Lots of noise, then locked up. Drum support bearings failed, locked up, twisted sideways.

  • Customer: Josh from interlachen FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
I made it very difficult. I didn't research the repair. My back is old. It's easier if you just You Tube a video. The top roller you have to take drum completely out. The bottom one, The one that failed for me, you can actually do it without taking anything apart. Access it at bottom back, two holes. I do not have small hands, it would have been easier. Channel Locks inside, 9/16th socket outside. That will loosen main axle. Then use short screwdriver or socket driver on small bracket connected to bottom of unit. Mine had one screw holding it in. Easy bottom fix. I don't really recommend replacing top till it needs it. You can only buy them by the pair too. You will be ready when time comes. I found top roller didn't actually need replacing, did it cause I had it all apart. Don't fix if not broke, right? Trust, BUT, Verify. Smaller hands, would have helped me. All I got.

no heat

  • Customer: Roy from Orlando FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
I have replaced the element, the thermal cut off switch. high limit thermostat and thermal fuse. Still no heat.... I am trying to figure out what part next. I could use your help.Roy

Dryer would not start.

  • Customer: Sam from JOHNSON CITY TN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Took back panel off. Did not have a clue! Went to Partselect Web site,entered my problem,BAM! instant solution.Watched repair video and was surprised how simple repair looked.Heck I can do this,no problem! I work from 7 A.M. to 5 P.M. so theres no chance to stop by local appliance part store before they close. Ordered my parts from Partsselect,arrived in just two days. Followed video instructions ,completed job in thirty minutes or less! I also got important information regarding maintenance and cleaning dryer to prevent fire hazard.Thanks,for help and saving me time and money.When I have a problem in the future I now know where to go.

No heat/timer wouldn't shut off.

  • Customer: Jay from Georgetown IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Pulled the back off, removed heating element and thermostat, installed new heating element and thermostat. This didn't fix my problem. Now I'm not sure what to do. I watched a video on diagnosing the problem on youtube. It helped me install the parts I bought. Now I'm not sure what the problem is as the ones I bought and installed didn't fix the problem. I guess diagnosing is my problem now.

would not heat up enough

  • Customer: Carol from Minneola KS
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
followed troubleshoot & repair steps provided by partselect.

Complete disassembly and diagnosis

  • Customer: jeff from bridgewater NJ
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I am more fortunate than most because I have extensive mechanical repair experience and my father has extensive electrical repair experience...he read the schematic while I placed the probes in the appropriate locations...I completely disassembled, cleaned, replaced all maintenance parts (felt gaskets [front & back of drum], drive belt, foam gaskets on heat exhaust duct)...the culprit was found to be the Thermal Fuse but I also replaced the Cycling Thermstat just because I serviced the entire heat exhaust duct (it had a fair amount of lint in it after 14 years...all other sensors on the heater unit and switches (door switch & centrifical switch (you will never find this unless you take out the drive motor [it is inside the drive motor] were tested and found to be good...all dash controls / switches were found to be in good order also...Part Select is wonderful to work with...they said allow 5 days but the parts were here in 2...! Just a little help for all of you out there...putting the felt gasket on the back of the drum will test your patience...it is a little smaller than the drum and as you get near the end with the glue it is extremely difficult to get on...I would recommend having a lot of clamps handy to hold the portion that is already glued to drum in place and another set of hands to rotate drum while you are stretching on the remaining foot...! One other thing...if you don't want to go thru everything I did chances are quite strong that if the dryer does not restart (after first failing) I would say to just order the Thermal Fuse for the 9-10.00...it is a pretty safe bet this will be your problem...I believe the dryer will start / restart even if the heater unit is no good and or the Cycling Thermostat goes bad since that just senses humidity...? The switch and fuse on the motor are not replaceable here...my father had contacts to get those parts from the motor company but...one is designed to stop the motor if it becomes hot which in all honesty I think would be pretty rare...it is in an open area...the other switch inside the motor prevents the heater from heating up until the motor is spinning which inturn spins the exhaust fan which is a safety feature but again I think motor failure is pretty rare.
All Instructions for the LER6620PQ0
1,726-1,740 of 1,847