Quick Question!

Have you ever purchased from PartSelect.com before?

Models > LEA30AW > Parts

LEA30AW (PLEA30AW) Amana Dryer - Parts

All parts for the Amana Dryer LEA30AW

Below is a list of all parts for the Amana Dryer LEA30AW - Electric. To find the repair part you need, you can browse the list below or you can narrow your choices by searching for a part by name or description.

All Parts for the LEA30AW
15-28 of 156
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$22.96

Roller Bracket and Shaft Assembly

This drum support roller bracket and shaft assembly is a little over two inches long. It is made of metal.

$5.21

BULB-LIGHT

Sold individually. This bulb is a 7-watt appliance incandescent light bulb. This appliance light bulb is two inches long. It is used for many clothes dryers. You will need a Phillips screwdriver and needle-nose pliers. Unplug the power from your dryer. You will find the light bulb by opening your dryer door and locating the casing surrounding the bulb on the top of the inside of the door. You will need to remove the single screw holding it in place to access the bulb. Twist the old bulb out of place. Use your pliers if the base of the bulb is still inside the socket once the glass part of the bulb has been removed. Check to make sure that the socket itself is not damaged. If the socket is damaged it will need to be replaced as well. Screw your new bulb into place.

$124.40

Motor Assembly (Threaded Shaft)

This 1/4 horsepower gas or electric clothes dryer motor carries 120 volts, 60 Hz, and 5.5 amps. It also performs 1725 revolutions per minute. This motor is used for some gas and so...

$7.00

Retaining Ring

The metal retaining ring, which is under an inch long, holds the rear wheels on the axels of the dryer. The main reason why it would need to replaced is if the retaining ring has sprung out of place or is damaged. Some the symptoms could be that your dryer does not tumble, it makes a loud buzzing noise, or if it pumps, but will not spin. The tools needed for this project are a putty knife, 5/16 nut driver, and snap ring pliers. Refer to the installation video and diagram for further instructions and guidance. Customers ranked this replacement project as easy.

$25.17

Blower Wheel

If your dryer is noisy, will not tumble, or is not producing enough heat, you may need to replace the blower wheel. This part is white in color, and is made of plastic. This part i...

$75.50

Lint Duct Assembly

This part includes the upper and lower air duct assembly and lint screen.

$4.63

Spring Retaining Clip

This spring retaining clip is just under 1 inch long. The clip is made entirely of metal and is attached to the back wall of the washer, under the console. If your washer is vibrat...

$15.70

Idler Pulley Lever and Shaft

This arm is what attaches to the idler pulley wheel.

$2.96

Screw

Sold Individually.

$23.32

Thermostat Boosting Heater

This thermostat heater is two inches long. It is beige/brown in color and is made of plastic.

$14.42

Idler Pulley Shaft

This shaft is made to fit the center of the idler pulley wheel of many clothes dryers. It is less than two inches long, and is made of metal.

$5.10

Screw, 8/18 x 3/8

This screw is sold individually.

$6.49

Single Felt Pad

This pad is used for many clothes dryers. It is made of a felt material and it is a little over an inch long.

$6.20

SCREW

All Parts for the LEA30AW
15-28 of 156