Models
>
LDG7304AGL
LDG7304AGL Maytag Dryer - Overview
Sections of the LDG7304AGL
[Viewing 7 of 7]
Keep searches simple, eg. "belt" or "pump".
Drum Support Roller Kit
PartSelect #: PS1570070
Manufacturer #: 12001541
The drum support roller (Dryer Drum Support Roller, Drum Roller and Washer Assembly) holds the drum in the proper position while it spins on the support wheels. This part rotates on the roller shaft w...
$13.50
In Stock
Tumbler and Motor Belt
PartSelect #: PS11757542
Manufacturer #: WPY312959
The tumbler and motor belt in your dryer allows the drum to spin during the drying cycle. At 100 inches in length, this dryer drum belt is 3/8 of an inch wide and has five ridges. The belt is black in...
$32.48
In Stock
Front Glide Kit
PartSelect #: PS1804752
Manufacturer #: 306508
The front glide is located at the front of the dryer, the drum rides along it. If you hear a metal-on-metal noise when your dryer is running, your front glide may be worn out and require replacing. Th...
$14.70
In Stock
Roller Shaft
PartSelect #: PS11743031
Manufacturer #: WP6-3129480
This roller shaft is also known as a support roller shaft or a drum roller axle, and is a part for your dryer. The function of this piece is to act as the axle for the drum roller; it provides a place...
$9.81
In Stock
Blower Wheel with Clamp
PartSelect #: PS2200270
Manufacturer #: Y303836
This comes with a metallic hub clamp to hold it firmly in place. The blower wheel with clamp is part of your dryer assembly. You will find this part attached to the drive motor shaft, which disperses ...
$22.88
In Stock
Retaining Ring
PartSelect #: PS11746909
Manufacturer #: WP9703438
This part is a retaining ring, sometimes called a retaining clip, that holds the drum support roller onto the shaft of a dryer. It is made entirely of metal and measures less than an inch in diameter....
$7.88
In Stock
Lint Filter
PartSelect #: PS11741140
Manufacturer #: WP33002970
This is a replacement lint filter for your dryer. Replacing this part is easy as it requires no disassembly of the unit. Make sure to clean the filter after every use of your dryer, and check the filt...
No Longer Available
Dryer Radiant Flame Sensor
PartSelect #: PS11741429
Manufacturer #: WP338906
If your gas dryer is not heating up or igniting, then replacing the flame sensor, located in the burner assembly, could solve it. This part senses heat from the igniter to monitor if it is hot enough ...
$47.91
In Stock
Drum Roller Shaft Washer
PartSelect #: PS11740748
Manufacturer #: WP312535
If you notice that your dryer is noisy or will not tumble, then you may need to replace the drum roller shaft washer. This drum roller shaft washer is just under an inch in diameter and is sold indivi...
$13.79
In Stock
Flat Style Igniter
PartSelect #: PS373025
Manufacturer #: 4391996
This flat style igniter comes with a wire harness connector. This part ignites the gas within the dryer. Bracket is NOT included.
$38.35
In Stock
Door Catch Kit
PartSelect #: PS2162263
Manufacturer #: LA-1003
This door catch kit is designed for use in dryers. This is an authentic OEM replacement part. This catch assembly ensures the door of your appliance will close, and remain closed. It allows your appli...
$32.34
In Stock
Idler Pulley Shaft Washer
PartSelect #: PS11757538
Manufacturer #: WPY312527
This idler pulley shaft washer is used with many clothes dryers. It is less than an inch long, and it is black in color.
$13.45
In Stock
Questions And Answers for LDG7304AGL
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the LDG7304AGL
[Viewing 6 of 6]Noisy
Fixed by
these parts
these parts
Show All
Door won’t close
Fixed by
these parts
these parts
Show All
Marks left on clothes
Fixed by
these parts
these parts
Show All
Drum Not Spinning
Fixed by
these parts
these parts
Show All
Too hot
Fixed by
these parts
these parts
Show All
Not Heating
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The blower fan (nylon) stripped off the motor shaft (steel)
Removed the front cover (screws on bottom 0f face)...removed blower cover....spring pliers to remove and install blower fan. the rest of the time was spent cleaning the inside of the shell as well as the vent. Reassembled and dryer runs better than it has for many years.
Parts Used:
-
Stephen from Lafayette, IN
-
Difficulty Level:Really Easy
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers
564 of 570 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Belt broke on old machine.
1. Removed front of machine (2 screws at the bottom).
2. Removed 4 screws from inside the dryer, to take off the blower housing.
3. Removed 4 screws and took out the large metal piece which supports the drum at the front. Removed the drum.
4. Replaced the two rollers that support the drum in the rear. Cleaned the pins they ... Read more run on, and oiled very lightly. Also replaced the idler roller. I was surpirsed to see that these rollers use plain bearings, not ball bearings.
5. On the front support piece, drilled out the rivets for the glides, and replaced the worn out glides with new parts. Applied a little glue (3M weatherstrip adhesive) to the cork pieces, to glue them to the metal. Attached the plastic pieces over the cork pieces, and riveted in place using rivets that came with the glide kits.
6. Replaced front and rear felt seals. This was not as tricky as I expected it to be. They were held in by metal tabs. Glued the ends where they came together.
7. Replaced the felt blower seal. Glued to the blower housing.
8. Reinstalled the drum, installed new belt, which came with good instructions (luckily).
9. Reassembled front support piece and the front of the cabinet.
I also cleaned the lint from the cabinet and from the vent hose.
In general, the job went without a hitch, and the machine probably has quite a few years left, despite the fact that it's 18 years old. This gives me a good feeling.
I'd say this would be challenging, though, for someone who is not pretty experienced with machinery repair. Also, the cost of the parts was significant enough that it would not have been unreasonable to have opted for a new machine.
2. Removed 4 screws from inside the dryer, to take off the blower housing.
3. Removed 4 screws and took out the large metal piece which supports the drum at the front. Removed the drum.
4. Replaced the two rollers that support the drum in the rear. Cleaned the pins they ... Read more run on, and oiled very lightly. Also replaced the idler roller. I was surpirsed to see that these rollers use plain bearings, not ball bearings.
5. On the front support piece, drilled out the rivets for the glides, and replaced the worn out glides with new parts. Applied a little glue (3M weatherstrip adhesive) to the cork pieces, to glue them to the metal. Attached the plastic pieces over the cork pieces, and riveted in place using rivets that came with the glide kits.
6. Replaced front and rear felt seals. This was not as tricky as I expected it to be. They were held in by metal tabs. Glued the ends where they came together.
7. Replaced the felt blower seal. Glued to the blower housing.
8. Reinstalled the drum, installed new belt, which came with good instructions (luckily).
9. Reassembled front support piece and the front of the cabinet.
I also cleaned the lint from the cabinet and from the vent hose.
In general, the job went without a hitch, and the machine probably has quite a few years left, despite the fact that it's 18 years old. This gives me a good feeling.
I'd say this would be challenging, though, for someone who is not pretty experienced with machinery repair. Also, the cost of the parts was significant enough that it would not have been unreasonable to have opted for a new machine.
Read less
Parts Used:
-
John from Charlottesville, VA
-
Difficulty Level:Easy
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers
535 of 658 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer Stopped Heating
If everything else is working ( tumbler and timer ) except for the heating. Your first bet would be checking your flat style igniter. Mine was cracked, something that I wouldnt have seen unless I had taken it off. Because of the crack no current was being passing through, therefore the igniter wasnt heating to its amber color. Since
... Read more
there wasnt any current the gas valve was doing its job by not allowing any gas to blow out. Dont worry about turning the gas off just disconnect your elecrical outlet. Remove whole front dryer panel by taking 2 front bottom screws out (philip screw driver). Dont pull to hard because there are two wires connected to the panel and dryer that you will have to disconnect. When you get to the igniter disconnect wire plug and use your socket set to loosen the single srew on the igniter, gently wiggle it out by just handling the white ceramic part of the piece, and replace new one in. Just remember to be careful since the dark part of the igniter that heats up is real brittle.
Read less
Parts Used:
-
Osvaldo from Albuquerque, NM
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers, Socket set
246 of 268 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!