Quick Question!

Have you ever purchased from PartSelect.com before?

Models > LDE8000ADL

LDE8000ADL Maytag Dryer - Overview

Get Parts and Repair Help for LDE8000ADL

If you know the dryer repair part you need, you can browse the list of all parts on the LDE8000ADL, or you can search by name or part description. You can also find your part by where it is located on the LDE8000ADL by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for LDE8000ADL parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$15.85

Drum Support Roller Kit

This drum support roller kit includes one drum roller and two bearings/washers. Most dryers use two drum rollers; it is recommended to change both at once. The drum support roller ...

Order within the next 7 hrs and your part ships today!
$14.96

Thermostat, Internal-Bias

A cycling thermostat is in tune with the temperature of your dryer and regulates it in order to maintain a certain temperature. This thermostat reaches a temperature of 155 degrees and will then turn off and then on again once it has dropped by 25 degrees. If your dryer is not giving off enough heat, is over-heating, is not turning on, or is having issues with the timer functionality, this could indicate an issue with the thermostat. The installation of the cycling thermostat is simple and the only tool required is a 1/4 inch nut driver (and gloves for safety).

Order within the next 7 hrs and your part ships today!
$13.81

Tumbler and Motor Belt

The tumbler and motor belt in your dryer allows the drum to spin during the drying cycle. If your dryer will not tumble, is noisy during operation, or will not start you may need t...

Order within the next 7 hrs and your part ships today!
$4.71

Roller Shaft

This roller shaft is also known as a support roller shaft or a drum roller axle, and is a part for your dryer. The function of this piece is to act as the axle for the drum roller; it provides a place for the roller to spin. The tools required for this repair include a stubby Phillips screwdriver, a 5/16 nut driver, a pair of snap ring pliers, and a 9/16 wrench. The first step before making this repair should be to disconnect your dryer from the power source.

Order within the next 7 hrs and your part ships today!
$9.89

Front Glide Kit

The front glide is located at the front of the dryer and the drum rides along it. If you hear a metal-on-metal noise when your dryer is running, your front glide may be worn out an...

Order within the next 7 hrs and your part ships today!
$15.05

Blower Wheel with Clamp

This comes with a metallic hub clamp to hold it firmly in place. The blower wheel with clamp is part of your dryer assembly. You will find this part attached to the drive motor shaft, which disperses air through the drum and out of the exhaust vent. This part might need to be replaced if you notice your dryer is taking too long to dry clothing, it is not tumbling, or is making any unusually loud noises. The blower wheel measures about 7.5 inches in diameter by 3-3/8 wide. The blower wheel can be accessed by removing the front panel of your appliance.

Order within the next 7 hrs and your part ships today!
$10.04

Lint Filter

This filter collects lint as it passes through the dryer vent.

Order within the next 7 hrs and your part ships today!
$2.92

Retaining Ring

This part is a retaining ring, sometimes called a retaining clip, that holds the drum support roller onto the shaft of a dryer. It is made entirely of metal and measures less than an inch in diameter. The retaining ring is a genuine OEM part sourced directly from the manufacturer. The ring may vary in appearance due to manufacturer substitution, but the function is the same. You may need to replace this part if the dryer is noisy during tumbling, will not tumble, or takes too long to dry. Be sure to check drum support roller kit and shaft before ordering parts.

Order within the next 7 hrs and your part ships today!
$8.20

Idler Pulley Wheel

This part is used to help the belt to rotate the drum. It is white and made of plastic with a metallic bearing in the center.

Order within the next 7 hrs and your part ships today!
$11.88

Drum Roller Shaft Washer

If you notice that your dryer is noisy or will not tumble, then you may need to replace the drum roller shaft washer. This drum roller shaft washer is just under an inch in diameter and is sold individually. It is located on the shaft of the drum roller, in the interior of your dryer. To access the drum roller shaft, you will need to remove the front panel of your dryer, and then remove the drum. Before completing this repair, be sure to disconnect the power source from the dryer. Tools required for this repair include a 5/16 nut driver, a stubby Phillips screwdriver, and a pair of snap ring pliers.

Order within the next 7 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

noisy rollers, broken latch

  • Customer: gerry from west covina,, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Wrench (Adjustable), Wrench set
  • 574 of 591 people found this instruction helpful
first, I unplug the power supply of the dryer then I removed the two screws at the bottom of the dryer then pulled out the front part of the dryer,unplugged the blue & yellow wire for the on/off switch for the door,at the back of the dryer I unscrew the pannel for the belt,disconect the belt,and I unscrew the four screws on both side of the front pannel to r... read more

The blower fan (nylon) stripped off the motor shaft (steel)

  • Customer: Stephen from Lafayette, IN
  • Difficulty: Really Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 536 of 536 people found this instruction helpful
Removed the front cover (screws on bottom 0f face)...removed blower cover....spring pliers to remove and install blower fan. the rest of the time was spent cleaning the inside of the shell as well as the vent. Reassembled and dryer runs better than it has for many years. read more

dryer squeeking

  • Customer: gerald from park city, MT
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set
  • 465 of 489 people found this instruction helpful
removed front panel,lifted top, removed drum and drive belt,remove old rollers and acc and instlled new and reinstalled dryer parts. read more