Quick Question!

Have you ever purchased from PartSelect.com before?

Models > LAV3600AWW

LAV3600AWW Maytag Washer - Overview

Get Parts and Repair Help for LAV3600AWW

If you know the washer repair part you need, you can browse the list of all parts on the LAV3600AWW, or you can search by name or part description. You can also find your part by where it is located on the LAV3600AWW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for LAV3600AWW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$50.48

Mounting Stem/Tub Seal Kit

This kit comes with hub assembly, agitator seal and spanner nut. If your washer leaks once full (with or without clothes in it) or leaks during agitation, then you should replace t...

$10.08

Adjustable Levelling Leg

Sold Individually. This adjustable leveling leg comes with a stop nut.

$48.36

Tub Bearing Kit

This kit is used on 2-belt washers. It is recommended to change the seal kit at the same time.

$21.71

Damper Pad Kit

This damper pad kit is used for base support. It comes with three six inch damper pads, two little tubes of lubricant. NOTE: This part will need adhesive to stick it in place.

$75.21

Agitator Auger and Base Assembly

This part does not include the dispenser cup that is found on the top of the upper agitator.

$23.74

Glide and Spring Kit

This glide and spring kit contains two three inch springs, four one inch square glides, and two tubes springs. This kit replaces older style round roller glides.

$4.94

SCREW

$174.69

2-Speed Drive Motor with Jumper Wire

This two speed split phase washing machine motor performs 1725 revolutions per minute in one speed and 1140 revolutions per minute in the other speed. This motor runs at 1/2 horsepower and it carries 8.0 amps. It's a good idea to change your washer's belts at the same time as you replace this motor, as they may have become worn as well.

$71.61

Tub Cover with Gasket

May not be exactly as shown.

$4.80

WASHER- CU

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

water leaking from around center shaft below fixed tub

  • Customer: douglas from bonita springs, FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Socket set
  • 405 of 415 people found this instruction helpful
My washer is 5 years old and water began to leak on the floor. I took off the front panel and filled the tub. Water did not leak immediately, but after the tub filled with about 3-4 inches of water, the water began to leak from a rubber washer between the fixed tub and the drive shaft. I looked online for exploded diagrams of Maytag washers, when I came a... read more

Drum would not drain and there was a banging noise when the drum spun

  • Customer: Charles from Whitman, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 220 of 115 people found this instruction helpful
I removed the 2 phillips screws on the bottom of the front panel. Then checked around to find the belts were actually below the floor panel.
I pulled the washing machine away from the wall and tilted it bacwards and found the pump belt was off the pully and the drive belt was badly damaged. I replaced the 2 belts which took no tools and about 3 minutes ... read more

Washer Leaking and Spin Cycle stopping frequenly

  • Customer: Dan from Mason, OH
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set
  • 146 of 152 people found this instruction helpful
* Remove front Panel
* Remeove two screws that allow the top to hing up.
* Loosen set screw on agitator (1/4" socket)
* Remove Agitator
*Loosen spanner nut from mounting seal with hammer and punch remember to loosen, turn clockwise
* Remove Inner Tub
* Losen Mounting stem with Hammer and Punch- Remember to loosen, turn clockwis... read more