Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Water overfilled tub onto the floor
The repair man shouldnt have opened his big mouth. He told me exactly what the problem was over the phone, but said he couldnt get to it for a few days. 20 minutes later I found the part and overnighted it to my house. Removed the back panel with a few screws. Couldnt have been easier.
Took a look at the new door switch assembly, used a socket wrench to remove the old, took wires off of old and attached them to the corresponding terminal on the new. attached the new assembly inside the top panel. Works!
Water was leaking from under the front of the washer when it was used.
After turning the water off and unplugging the machine, I took the front panel off the washing machine. I then slipped the belt off the pump sprocket. The pump was right in the front and easy to remove. All I needed was a screwdriver, for the hose clamps, and a 5/16" socket to remove the old pump. I then installed the new pump, with the existing screws, re-attached the 2 hoses, slipped the belt back on, and popped the front panel back into place. The new pump works great and the leak is gone. The whole job onlt took about 30 minutes.
Resin balls on which the top loader lid hinges had broken.
Cleaned the cavities. Lubed them with olive oil. Inserted one ball on left side, while holding tension against that side to hold the ball in the lid and top indentations. Applied olive oil to right hand side indentation, and placed the new ball into lid indentation. Put lid down into closure cavity with ball, and with lid vertical, began pushing it rearward so as toslightly spring metal lid rolled edge and top metal away from one another UNTIL the new ball snapped into the hinge indentation in the machine cover. Done.
Our Maytag (A308) washer is now about 29 yrs old. I put in a PartSelect water valve 3 yrs ago. When it started leaking recently I found the cuplrit to be a flexible hose to the outer basis. The front came off easily (two screws at the bottom) and the hose clamps required some cleaning. I recommend purchasing new clamps. Under 30 minutes to get it running again.
First closed hot & cold water faucets feeding the two washer water hoses, then turned the machine on fill momentarily to bleed off water pressure in hoses, and unplugged power cord. Used pliers to help break seal on brass hose ends, removed old hoses. Removed 1/4 & 5/16 sheet metal screws, replaced leaky valves. New assembly was EATON Made in USA, high quality. Replaced rusted outlet hose spring clamp with "IDEAL" stainless screw clamp. Replaced unit in machine, installed new hoses, runs fine.
Unplug from electrical outlet.Unscrewed control panel and laid it open. The switch is in 2 parts. Removed wires and unscrewed each switch. Put wires back on and tightened switch back to mounting plate. No brainer. Tried washer and worked perfectly. Two tips: Check fuse on plate to make sure it isn't burned out before ordering any parts. Secondly when installing if you have older model washer there is a nib that sticks up on mounting plate that keeps the switch from installing correctly. Cut this nib off with a wire cutter and then install. The directions don't mention that.
Overloaded my washer and broke the water-injector!
Had to look up how to pop the front panel off the washing machine - that was the hardest part. Once that was off, the top unbolted and the cover came off the back of the control panel with a few screws. Tilting the washer-top back, I was able to clip the new upper and lower injector (attached to each other in advance) to the washing machine. Then I realized that I needed to clamp the water line to the injector FIRST - so I found a small screw clamp and attached the water line. One screw and one plastic tab hold the injector in place. Everything went back together fine and worked great! Maytag washer keeps on truckin for another ten years!
There are two screws that hold the switch in place. And two wires connected to the switch. The most difficult part of replacement is to place the new switch and hold it in place to reinstall the mounting screws. The space to work in is limited unless you remove the front panel from the dryer, which I opted not to do.
found water on floor checked it out found water mixer leaking.
shut off water to machine remove water mixer removed bracket. Installed new part put back together, turn on water, start washer all worked as it should. Really like your parts selection. clayton