All Installation Instructions for Maytag Washer LAT2000AAE

Would not agitate

Followed video instructions. Most difficult part was re-installing the E-clip on the bearing.

Parts Used:

Transmission Pulley and Bearing Kit

Willie from Pensacola, FL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Washer would not agitate

Tilt washer back to expose the bottom. Remove broken belt. Install new one. Do a test run: Washer is back to working fine. Note: My boyfriend actually did the repair while I was at work, but reported that I could have done it myself easily. Also: FedEx delivered the part on a Saturday without an extra delivery charge, so my washer was repaired several days sooner than I anticipated. Thanks, PartSelect!

Parts Used:

Drive Belt - 51 inches long

Dawn from Franklinton, NC
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

Burning rubber smell & noisy

Pulled the washer away from the wall, tilted it 45' pulled belt off loosened the bolt on the motor belt tensioner & installed new belt.

Parts Used:

Drive Belt - 51 inches long

Joshua from Barnsdall, OK
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Wrench (Adjustable)

Was this instruction helpful to you?

Thank you for voting!

Drive Belt shredded and fell off.

The repair was very simple. We got the part faster than we thought we would had our son hold the washer on a tilt and put on the drive belt, took 2 times because it was twisted but we got on. The washer is much quieter and it was worth the shipping fee.

Parts Used:

Drive Belt - 51 inches long

Valerie from Steger, IL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

Drain pump pulley stared making sqeaking noise

turn off water to washer, disconnected hoses. Tilted over to open rear access panel removed old worn part replaced with new part reattached pulley. Replace access panel flipped back in operation position. Connected hose turned on water. Put small load in and turned on washer worked great.

Parts Used:

Drain Pump with Pulley

JASON from ARLINGTON, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set

Was this instruction helpful to you?

Thank you for voting!

Washer jumping around during spin cycle

I used Utube to search for Performa Washing machine jumping around. You will find several videos that will be extreamly helpful in understanding exactly how to go about changing the sunbber ring. The snubber ring is fairly easy to change out. Quarters were used to hold the springs apart so they can be removed. Push the tub forward and away from the spring you want to remove. Install several quarters in the spring. Use as many as you can get in. Then pull the tub toward you and the spring can be removed from the tub. There are six springs to remove. I just left them laying in place at the bottom of the washing machine base. There are videos on utube also of using the quarters to remove the springs. Of course if you have spring removal tool for this purpose so much the better. I didn't have one. Good luck with your install. MB in TN

Parts Used:

Snubber Ring

Michlen from Kingsport, TN
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers, Socket set

Was this instruction helpful to you?

Thank you for voting!

Washer wouldn't drain

I heard buziing and smelled a burning smell with my washer so i got on your website and watched a video how to take the washer apart and what the problems could be and determined it was the drainpump so i took the 3 bolts holding it on out and inspected the belt while i had it off , and ordered the part from you guys and put it on your information was very helpful

Parts Used:

Drain Pump with Pulley