KUIC15PLTS4 KitchenAid Ice Maker - Instructions

I replaced the thermometer first and it started working again. I was convinced that the reason that it continued to break every 6mos was because no one had ever replaced the fan. The difficult part was getting to it. After trying to get in from the front and from the back I finally figured out that I had to take the bottom off and tilt it on its side. I was then able to get out the pin in the condenser and move it to the side. I could then reach the screws that held in the fan. I then decided to put the fan on the motor and when I was tapping it on with a hammer the back cracked. I attempted to fix it by taking apart the old motor and salvaging the parts but that didn't work. I had to buy another $85 part and take the whole thing apart again. It was easier the second time because I knew which screws and pins I had to remove and how to get to them. I very, very carefully tapped the fan onto the motor and now it is working fine. I will let you know if it is still working at Easter. If it is I will have done a better job than the 7or 8 repairmen who have fixed it in the past

Repair was so simple, I didn't even need instructions. Removed old fan with motor, installed new one, installed harness that converted plugs, done. Saved hundreds of dollars doing the repair myself.

Removed to old motor by removing screws and disconnecting power source and replaced with the new motor and plugged back in power source

Using a 1/4" ratchet removed the old motor, a bit difficult due to small space to get your hand and ratchet in position. Before installing the new motor I used one of the screws to tap the the 3 holes in the new motor so it would be easier to start the screws attaching motor to mounting bracket. Attached cable. plugged in the fridge. Great to hear a quit running refrigerator again.

Before I began I unplugged the electrical at the wall outlet. 1. Unscrewed the 4 mounting screws. 2. disconnected electrical at the motor. 3. removed the assembly. 4. mounted the new motor on the assembly as described in the instructions. Installed the assembly and reconnected the electrical. Works great, easy job!

A bit of a tight squeeze for my hands, but very basic as I followed the instructions and watched the installation video. I only had the fridge unplugged for about 20 min..The fridge is as quiet, as it was brand new. The only tool I needed was the 1/4 inch socket wrench. A portable lantern was very helpful as well. Runs very quiet now, like new! Thx!!!

Took out one strap support with a nut driver, unplugged the device and plugged in the new one. Reinstalled the support strap. Job complete.

Fast after a little help from a friend

Removed old assembly by disconnecting 2 wiring harness connections and loosening 2 screws with nutdriver. Installed new assembly using same process. Had ice in about an hour. Very easy.

Pretty much followed the how to video. Biggest pain was removing the screws to the bracket that houses the motor.

as told per compter

Removed and replaced the condenser motor fan kit. This was a very easy tear down and replacement of a bad component. Removed 4 screws to remove the bracket holding the fan motor kit pulled it out and replaced with the new unit (4 screws supplied) plgged in adapter cord (supplied) and re-installed took about 10 minutes.

I removed the two screws that hold the shield in front of the grid and put them aside allowing access to the grid. I then removed the two screws that hold the grid in place. I unplugged the connector and then pulled it out. I reversed the process to reassemble and powered up the unit. I now have ice again. This whole process probably took me 15-20 minutes to do the install.

fan motor housing had to be drilled through both sides of housing to attach to existing bracket. Possible damage to wiring inside the unit may disable condensor fan motor when motherboard is replaced. (Motherboard on order.)

remove the front cover by removing two screws. then remove two screws with a nut driver on each side. unplug the wireing harness from the top of the unit (may need pliers for this) the pull the unit out. then slide the new unit in, connect the wireing harness, install two side screws, and install the front cover and wham you will have ice in about 30 minutes. thanks parts select. you were very easy to deal with