Models > KUIC15NRTS0 > Instructions

KUIC15NRTS0 KitchenAid Ice Maker - Instructions

All installation instructions for KUIC15NRTS0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the ice maker repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KUIC15NRTS0
16-30 of 96
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Loud noise

  • Customer: Britney from Wilmington OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 6 of 6 people found this instruction helpful
There was a loud noise coming from the fridge - we ordered the new part it came a lot sooner than we excepted and we replaced it in about 20 minutes- the hardest part was my husband getting his hand in there to put the screws in- but a very easy fix.

Motor was making loud noise.

  • Customer: Stephen from Purcellville VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 5 of 5 people found this instruction helpful
Unplugged refrigerator, Removed lower back panel, Removed fan from fan bracket, Installed new fan to fan bracket, Installed new wire assembly to fan, Replaced back panel. Plugged refrigerator back in and it works great. Only tool needed was 1/4" socket.

broken ice cutter wire

  • Customer: Leo from Ormond Beach FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 5 of 6 people found this instruction helpful
remove tray from icemaker by removing 2 screws and disconnecting 2 electrical connectiona. Remove broken wire and restring new wire. Reinstall tray.

cutting grid wire was broken

  • Customer: Audrey from Morrow GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 5 of 6 people found this instruction helpful
removed broken wire, replaced with new wire and screwed the 6 tensions screws to tighten the grid wire.

Ice Maker was not making normal ice and was making noise.

  • Customer: Julie from New Braunfels TX
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required:
  • 5 of 7 people found this instruction helpful
Emptied ice from bin. Drained water. Added cleaner and started clean cycle. When done, restarted ice maker. Works great now!

fan making bad bearing noise

  • Customer: Bruce from Malvern OH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 5 of 7 people found this instruction helpful
r&r fan blade and motor. with the parts you supplied it was easy. the parts were perrrrfect. thank you very much. job well done. bruce

Water not flowing over cooling plate

  • Customer: Tom from Galesburg IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 5 of 7 people found this instruction helpful
Removed ice scoop and holder. Remove front cover and pump bracket. Replaced pump and replaced covers. Started up and working well.

water inlet valve was leaking and damaged the circuit

  • Customer: Hugohug from LAREDO TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 8 of 17 people found this instruction helpful
just replaced the water inlet valve, it took less than 10 minutes. Ordering the part was just as simple, no hassle what so ever. Got the part as promised and installed it in minutes just as it was explained. I will come back to this site in a hart-beat.

Thanks

fan bearnings wornout

  • Customer: Thomas from Grand Island FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 3 of 3 people found this instruction helpful
Simple remove the fan and motor, plug in the new cord and screw in the new motor.

Broken wire on the cutting grid.

  • Customer: Jeffrey from Duluth GA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 4 of 6 people found this instruction helpful
Removed the grid.
removed the existing top to bottom wire.
restrung the grid with the new wire.
Then, it cut ice just fine-better than new.
Note:
wire provided is only sufficient to rewire side to side or top to bottom, not both. If you need to do both, you'll need 2. Yes, lots of money for a few feet of wire.

Loud noise coming from rear of fridge.

  • Customer: Gerardo from Berwyn IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 3 of 3 people found this instruction helpful
It was very easy. The part make look different online but it was a proper replacement.

condenser fan making growling noise

  • Customer: Mark from Green River WY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 3 of 4 people found this instruction helpful
pulled fridge out, remove back cover, remove 4 screws holding fan put new fan in with new screws way easy dont call a repair man for this shipping was fast thank you for that

Noise when compressor was running

  • Customer: John from Medina OH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 3 of 4 people found this instruction helpful
I recieved the replacement part the next day after ordering it. If you are some what mechanicaly talented this repair is very simple. The only tool that is needed is a nut driver. You may want to remove the bracket holding the water solenoid vavlves. Then you can pull them out of your way to remove the 3 screws holding the fan to the bracket. Once you remove the old fan motor just reverce your steps with the new motor. Check that all your screws are tight. Check to make sure that there are no wires in the way of the fan. Don't forget to attach the wire harness and re-attach the solenoid bracket. Ahh nice and quiet like new!

Stopped making ice

  • Customer: LARRY from INDIO CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 4 of 7 people found this instruction helpful
I called a repairman to come out and he said it would cost $320 dollars for the repair. So I bought the part and spent $85 dollars and about 25 minutes to repair it myself

Reservoir for water had cracked and wasn't holding water

  • Customer: Dan from Sandy UT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 4 of 8 people found this instruction helpful
removed two screws and bracket that held it in place. Removed the hoses and pump. put new one in by re-attaching hoses, pump then put screws back in to hold it in place. Fairly easy.
All Instructions for the KUIC15NRTS0
16-30 of 96