KUDY24SEAL0 KitchenAid Dishwasher - Instructions

The part that was supplied was not completely compatible with my dishwasher even though the model number entered was correct and even verified by telephone. I watched the Youtube video provided and the assembly arm did not attach the way it was shown on the video. I had to combine some original parts of the dishwasher with some of the parts purchased to make this work which took a lot of extra time and addn tools. I feel the instructions/part were not as advertised.

removed top basket clips, removed basket from slides, removed middle spray arm assembly with screw driver, replaced with new middle spray arm kit, put basket back in slides, put clips back on and done. new kit much better design.

watch the video on line and it was very to do.

After attempting to change the "high limit switch" to no avail, I researched further and found that doing a reset/reboot cured the problem.The instructions for the high limit thermostat were a bit off, as there was no screw to remove, only a spring like bracket that I did not try to figure out. The work area is so tight if the dishwasher is not removed and tilted that I thought it best to look for alternatives prior to pulling it out and disconnecting power and water. So ... voila, it's fixed with a reset only. Reset is accomplished by pushing two buttons 5 times. "high Temp Scrub then Heat Dry, high temp scrub then heat dry etc, until you click them both 5 times.It will go through cycles for a few minutes, then after done, run the dishwasher as normal and test if fixed. There are a few different ways to do it depending on the model.

i took the inside door off and took the 2 switches out and replaced them; not too difficult.

I could not find a 90 degrees 1 inch car wrench and by them the impeller head wish is plastic was all run down so nothing will hold it, finally, I heat up a flat screw driver and cut the impeller near the head whit the help of a hammer , and them I could grab it with a pressure wrench and loose the screw up. finally the fix when fine and is working good. the parts are just the ones I need it. Thank you.

I read information on this website about the function of the high limit thermostat. I found that it was the problem by disconnecting the two wires on the thermostat and straight wiring to bypass it. This allowed the machine to work properly so I ordered the high limit thermostat. To replace the part I used a screwdriver to remove the instrument panel and replaced the high limit thermostat by disconnecting the two wires from the old thermostat and connecting the wires to the new thermostat. I then replaced the instrument panel. My machine is working properly again..

Purchased the middle spray arm kit from Part Select.. I removed the old spray arm with a Phillips screwdriver and installed the new arm and tube. It was a very easy and self explanatory installation. The instructions provided were easy to follow.

I ordered the kit that included a new water sprayer. I took apart the old parts and watched carefully how each part went together and did so with the new kit. It was so easy and took less then 15 mins. I was very proud of myself. I have started to fix things around my home instead of calling repair people and finding it's not hard at all if u just use common sense. I just finished redoing my main bathroom and plumbed everything. I also put a new deadbolt on my front door.

Took the broken parts and model number, went to your site and looked model. The diagram was easy to use and figure out the number for each part.Once the parts arrived a few days later, it was just a matter of following the diagram and it took no time at all.

My model was DU7600XS0. I disassembled according to the video and the parts diagram here. I found a piece of metal, a pebble, and a wrecked drain impeller. I cleaned out all the debris and began reassembly. I found that the chopper blade shipped with this kit has a lip and will not fit over the metal drain impeller sleeve on this model. It needs to, or else it will not screw together properly and the impeller will not be able to turn. My old one was undamaged, so I used that instead. Also, the large black wash impeller has a shaft that is longer than the original part and because of that, it would not screw on. Again, the original wash impeller was fine, so I used the old one. I replace the gaskets and screwed everything else back together. It works great now. No water is left after the cycle anymore and the sound it makes is back to normal. Money well spent on this kit!