KUDS50FVWH3 KitchenAid Dishwasher - Instructions

1. Removed front panel. 2. Backed out retaining screws at top. 3. Backed up leveling feet. 4. Pulled out dishwasher but seemed tight so stopped not wanting to break electrical or water line. Made very short space in which to work. Insulation batting was binding at top between DW and counter opening so tended to bunch up. 5. Spring at rear had flown off, so had to reattach while not being able to see. 6. Spring and new line were very tight so grabbed line with channel pliers just ahead of spring to get enough slack to get line over guide wheel. 7. Moved DW back into place and reattached with screws. 8. Had to play with leveling feet to get gap the same on each side of DW and cabinet opening. 9. Reattached lower front panel. 10. It has worked great.

Remove blown high limit therm.and replace with the new high limit

removed old one and replaced with new one, in about 30 mins.

Our Kitchen Aid dishwasher was not getting the dishes clean so I went on line looking for a fix that did not include replacing the dishwasher. Found the Parts Select website, read a few of the comments and ordered the pump / motor assembly. Following the steps of others, I turned off the dishwasher at the breaker panel and disconnected the power. I found it easier to disconnect the water feed and drain under the sink rather than under the dishwasher. The dishwasher was held in place with 2 screws at the top, It came out easily. Warning: have towels handy as the water in the drain, inlet and housing will come out with the removal of the dishwasher. I did have to remove the upper spray assembly, easy, to remove the motor / pump assy. the assembly is held in by three plastic clips. When these are removed, the assembly pulls out through the inside of the dishwasher. Replacement was simple, just reverse the steps in removal. Be careful to center the pump / motor assembly. Having done this once, I would probably leave the dishwasher in place and change out the pump / motor assembly.

rinse cap was put in and turned to secure.

Replaced the Pump Motor and Housing Assembly. Generally the video did very well in showing what to do. However, it underrated the difficulty of getting the assembly to fit properly and seal in place. The clamps to secure it were difficult, but eventually got it through about 5 repeated attempts. Now after first us, it is working well.

followed instructions in pkg.

I had to pull the dishwasher out from the cabinets about 12" in order to pull the old seal off. Installing the new seal was quite easy, since there is no adhesive necessary. Start at the top center of the replacement seal and snap the groove of the seal which is hard plastic, into the mating parts of the tub and the tub trim. Its a little hard to explain, but pay attention to how the original seal (W10179427) was installed.

Lifted out the old damaged cap; replaced it with the new one. No tools needed. It took one minute. The company had the part sent out to us immediately; it arrived within a few days. The whole process of ordering, receiving, and repairing was super convenient.

repairman replaced the valve inlet; first website tried to tell me I needed a new pump, but repairman said it would be some type of valve; service rep on phone very helpful,I ordered the correct part,except for having to lay on the floor, he repaired it easily; part came within 24 hours. Worked immediately. No additional tubes or parts needed.

I read information on this website about the function of the high limit thermostat. I found that it was the problem by disconnecting the two wires on the thermostat and straight wiring to bypass it. This allowed the machine to work properly so I ordered the high limit thermostat. To replace the part I used a screwdriver to remove the instrument panel and replaced the high limit thermostat by disconnecting the two wires from the old thermostat and connecting the wires to the new thermostat. I then replaced the instrument panel. My machine is working properly again..

First I shut off the power and the water then I disconnected the drain hose. Then I removed the dishwasher from under the counter and turned it up side down. I remover the pump retaining screw turned the pump, removed it. installed the new pump reinstalled the retaining screw. and reinstalled the dishwasher under the counter. I reconnected the drain and water then turned on the power. the dishwasher is working great. Thanks PartSelect for the fast delivery and the right part.

The dishwasher was so load I was sure the pump had a bad bearing. . . After reading the on line comments I examined the chopper and it looked ok. As it turned out the damage was on the shaft and caused the shaft to lock onto the screen without the ability for the spring to work it must have caused excess pressure making the loud noise. I replaced the chopper and now the dishwasher is very quiet again. To replace I took out the baskets and four screw on the big screen and one more screw on the chopper cover then I had to pull on the chopper with moderate force and install the new one . Then I put back the covers and basket. . . Very easy

Took out the old basket, set in the new basket. Took all of 10 seconds to complete.

Installed brackets