First, I bought the door balance link to replace the broken links that connect to the springs.
Because I didn't have enough slack to simply pull out the dishwasher far enough to reach the springs, I had to disconnect the water line and electrical wiring. The only reason my repair took as long as it did was because there was so little room underneath the dishwasher for disconnecting the water line. I had to buy a shorter adjustable wrench. Also, I had leaks after reconnecting the water line. I had to tighten the compression nut as far as it would go. The nut wrapped around a white substance that had been applied to the threads (I believe this is called pipe tape), which did the trick for sealing the leak.
The repair was a complete success! The parts arrived fast and the information from other customers on the the PartsSelect website was invaluable.
thought it could be due to the overfill control switch,so ordered one and replaced one in the washer. However, it did not solve the problem. Having a repair company coming to look at the dishwasher. Tipped the washer on its back and switch was readily accessable. Only had to open plastic covering over the switch, disconnect the wires and install new switch and reconnect the wires.
Hardest part was pulling dishwasher away from cabinet, making sure to not disturb water and drain line. I replaced both door springs which are on the two sides and attached to the dishwasher frame towards the back. This necessiatated pulling the dishwasher about 2/3 out of cabinet. After attaching both springs to frame, replacing the balance kit was a breeze .One screw to remove and then replace with new pulley unit. Attach the supplied cord with attached fittings to spring and then around two pulleys and mounting point on frame. Done . Push dishwasher back into cabinet, reattach two screws to underside of counter. Probably did not require new springs as they seem heavy duty and were not broken upon examination but ordered them also and replaced just in case. Most problem would be with broken cord in balance link kit
No instructions provided; Star driver included but useless
This repair is simple. However, what you recieve is a box of loose parts and no instructions. The new parts are not remotely the same design as the original. You have to figure out how to remove the old parts (fairly easy by careful prying) but then sort out what the new parts do and how they fit together. It takes patience and some mechanical knowledge. Once you figure it out, it goes quickly. A fairly simple diagram included with the parts would be definite benefit for most people. It seemed like an odd omission. They also include the shortest star driver (about 1 inch long) I have ever seen for the 4 screws but it is useless since you can't really apply enough torque to the screws to properly set them. Be prepared with a standard length star driver.
I Removed the upper wash rack by removing locks on each front slide of rack. I laid a towel in the bottom of the washer to keep anything dropped, retrievable. I then removed the top screw closest to the spinner location. I then carefully pulled down on the mounting, which exposed the bad bushing lock. I removed the old bushing lock and replaced with new one. I then replaced the spinner with a push with one hand while holding the bushing in place with the other hand. You will feel a snap as all goes into place. Make sure new spinner spins freely. Now reinstall removed screw. Do not over tighten. Now reinstall lower rack, carefully aligning water feed in rear of washer, and making sure all rollers are back in sliding rack. Reinstall locking tabs onto sliding rack. Now slide out rack, it should not come off slider. Important: now remove the towel in the bottom of the washer. If left in place, you will have a fire during the drying cycle. Close the door and test your washer through a cycle. I felt confident and did a load of dishes. If all went well, spinner should be in place, not in the bottom of the washer.
Pulled upper tray out. Removed old adjusters and replaced with new. The pictures in the installation instructions were bad (blurry and hard to distinguish). Had problems with the first side button. Put it in before installing the wheel base on the second side. Went much easier that way. You did need a star tip for the screws.
Watch your video about my dishwasher symptoms. Move water tube for upper rack to the right and release lower spray arm. Remove 4 clutch head screws from filter cover and remove. Dig out 10 years of undisolved soap and reassemble.
Looked on you-tube and it was so easy. Pump on bottom right. unplug pump and do a halfway turn. Plug the new one up and place the pump on, and turn halfway and its on. START your dishwasher
I did not get to repair my dishwasher using the part supplied by Partselect.com. I pulled my dishwasher out and found that the connector had fallen of the capacitor during installation. Happy to say that I returned the part for a full refund minus the shipping. Have bought from them before, and will again
First I would like to say I was concerned about undertaking a dishwasher repair ,as I now am legally blind and I was concerned that my vision impairment might cause me a problem. My dishwasher pump motor was not running and from the humming sound I could tell it was cycling power off on the thermo switch overload. The pump can be removed by turning it counter clockwise,however it would not move and I could not rotate the motor manually, IT appeared that the impeller must be jammed,so I removed the complete ascribe..After I removed it the motor still could not be removed for replacement. I ordered the complete assembly from PartSelect.com an was supervised how fast it was delivered. The hardest part was getting the seal to go in place as it was new and a tight fit. The Partsselect.com video's ,on repair instructions were very helpful. I reinstalled the dishwasher and everything worked fine.Thanks for thefast delivery of my order.
