KUDS30IXBT2 KitchenAid Dishwasher - Instructions

It was a simple snap it apart, put it back together using the new parts. Very simple. A small screw driver was used to help pry the snap together parts apart. No tools needed for reassembly.

I had to pull the dishwasher out from the cabinets about 12" in order to pull the old seal off. Installing the new seal was quite easy, since there is no adhesive necessary. Start at the top center of the replacement seal and snap the groove of the seal which is hard plastic, into the mating parts of the tub and the tub trim. Its a little hard to explain, but pay attention to how the original seal (W10179427) was installed.

Very easy if you are mechanically inclined

Really was repair. Pulled rack out of glides unclipped the broken rack adjustor, clipped in new one, using opposite side as a guide for the clips

First I shut off the power and the water then I disconnected the drain hose. Then I removed the dishwasher from under the counter and turned it up side down. I remover the pump retaining screw turned the pump, removed it. installed the new pump reinstalled the retaining screw. and reinstalled the dishwasher under the counter. I reconnected the drain and water then turned on the power. the dishwasher is working great. Thanks PartSelect for the fast delivery and the right part.

All parts snap together. Following the the rack on the right side, If i can do it anyone can. It was great to save the cost of a repair bill.

First, open the stops at the end of the tracks and remove the upper rack. Use a screwdrive to gently pry off the main clip (with 3 tiny plastic tabs) that attaches the rack adjuster to the rack. Remove the two positioners. It was a little tricky removing the piece that covers the housing of the rack adjuster which rotates into position. I ended up breaking one of the brittle wheels on the rack adjuster on the other side during the repair when I set the rack on its side. Be sure to order rack adjusters for both sides at the same time--don't just replace one side, because the other roller wheel pins that attach the rollers are equally fragile.

The dishwasher was so load I was sure the pump had a bad bearing. . . After reading the on line comments I examined the chopper and it looked ok. As it turned out the damage was on the shaft and caused the shaft to lock onto the screen without the ability for the spring to work it must have caused excess pressure making the loud noise. I replaced the chopper and now the dishwasher is very quiet again. To replace I took out the baskets and four screw on the big screen and one more screw on the chopper cover then I had to pull on the chopper with moderate force and install the new one . Then I put back the covers and basket. . . Very easy

pieces snap together - having the new piece made it easier to figure out how to dis-assemble the broken part from what had to remain with the new one. Not obvious in all cases how it comes apart but figured it out in a few minutes - have to be careful not to break anything else.

Very easy to repair. Took off two supporting clips, opened up the shelf adjuster and replaced part. Be careful prying open the adjuster

you need to remove 3 clips which is very easy and straight forward. The more difficult part is removing the adjustment slide, the main part. A few words of instruction with the part would have been very helpful. I kept moving the part around until it snapped out. Realignment to put the new part back in was trial and error. It finally slipped in and reinserting the three clips was easy.

I bought only ajusters #4 and used the old #5,#6,#3,#9.If you think they may break you might whant to order these also.Study which side of rack the part is on that you are about to remove.Dissconnect part #5 from rack and slide down to remove from #4.Slide #6 down to remove from #4. Part #3 has two pins on back side ,squeeze and push to remove from #4. #9 has two pins on either side at bottom,use screw driver to push out sides of part #2 to remove pins from holes.Top will slide down out of slots at the top of #2. Assembly- Start with #5and #6 to help hold adjusters in place,then #3 and #9. I hope this will help you.

Installed brackets

1. Remove top rank. Do this by opening the clips at the end of each railing. This allows the rack to slide out. 2. With a screwdriver take apart the rack adjuster. Be careful not to break the adjuster clips. 3. Reassemble new rack adjuster with clips. 4. Hint: Take apart and reassemble each side separately. This way you will always have one assembled side as a reference when putting everything back together.

The part was easy to install. But , you might have to unhook electrical, water, and drain. That is the time problem, part install is easy. All I had was a socket set, 1/4, drive fits. But a nutdriver would have been easier. WATCH the install video, great info!!!!!