KUDS21SS1 KitchenAid Dishwasher - Instructions

I unscrewed the screws and slid the panels in. Very easy. I wanted all the appliances to have a stainless steel look.

It was easy to remove rack from dishwasher. I screwed on rollers and it was like new!

I pulled off the broken parts and snapped on the new axles, then replaced the wheels. Very simple.

i pulled the rack out, took off the old parts then added the new ones. it was quick and simple. i needed no tools and my package of parts arrived quicker than i thought. thanks!

I ordered 8 new axles and used old wheels. I broke off the remaining axle parts left on the wire lower basket with just my hands, and then popped on the new axles. This was done without tools; just needed significant pressure to pop the axles onto the coated wire. The wheels popped onto the axles with a little pressure. Make sure you have the right side of the wheel out. I simply looked at the remaining working wheels before install began to make sure which side goes out. Very easy install.

We have a remote cottage in Canada with a dishwasher over 30 years old. Since you have to get there by boat we didn't want to have to get a whole new dishwasher installed. The plastic rollers from the top shelf had fallen apart and the top rack would fall off all the time. My daughter found your company online and ordered the exact parts for me! I couldn't believe it. For about $20.00 my dishwasher was fixed by my husband in less than a half hour. It was easy to order the parts from you, they were shipped immediately and worked perfectly. Thank you so much for your help with our dishwasher parts. I was laughed out of Lowe's, Home Depot, Sears and H.H. Gregg when I took my old parts there looking for help with replacement parts. I would recommend your company to everyone.

removed screws from dishwasher and discovered i could replace panel because of door type

Simply replaced the wheels/axiles and brackets using functioning ones as template. No problem at all.

first-removed all axles from one side of rack. replace with new ones, replace rollers. repeat for other side of rack. VIOLA!!

Closed water supply--Turned circuit breaker off to dishwasher--removed lower panel on dishwasher--removed the two wires from water inlet valve--disconnected water supply line--removed angle fitting from old valve & installed in new valve--reinstalled new valve & connected water line & 2 wires--This fixed problem.
I ordered part 11:00 1/15/09--Recd. new one 10:30 next morning. VERY FINE SERVICE & PRICE from PARTS SELECT.COM--Thanks.

I took out the bottom rack, turned it upside down, popped off the wheels and saved them and put on the new axles. It took a little doing to get the new axles snapped into place-they were stiff. I finally figured out how to use the pliers at the right angle to pop them on. Then the wheels popped right on and off I went.

I ordered all new axles even though not all of them were broken - I figured it was just a matter of time. Ordered one new roller because one was missing, and an extra one just in case. Removed all old rollers and axles. A couple of them did not want to come off, so I "hit" them with a screwdriver. Put on all new axles and replaced the rollers. The whole project took about 10 minutes. SUPER EASY. CHEAP FIX FOR MY OLD DISHWASHER.

The website had great pictures, I compared the wheels I had and the broken axles with the pictures, and picked what I thought would match. They were perfect. I used pliers to pop the axle on, and my fingers to put on the wheels. It works perfectly now

we used hot water to soften the ends of the tube and then slid it onto the two ends of the parts in the dishwasher. It did take a little bit of "push" to get it on one end, but nothing we could not handle. I would say anyone with common sense and willingness to fix something them selves would have no problem. I would like to say the part I ordered was of good quality and saved me a lot of money.

I put a whirlpool tube on my Jen more dishwasher . Fits like a glove.