Models > KUDP01FLSS6 > Instructions

KUDP01FLSS6 KitchenAid Dishwasher - Instructions

All installation instructions for KUDP01FLSS6 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KUDP01FLSS6
76-90 of 737
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Pump Motor not working

  • Customer: GLENN from CHEPACHET RI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 7 of 7 people found this instruction helpful
1, I shut off ac circuit breaker.
2.Shut off water supply valve.
3.disconnected water line from inlet valve.
4. disconnect the drainage hose.
5. have plenty of towels to mop up water.
6. Remove racks and disconnect water diverters inside the tub.
7. remove phillips head screws that hold dish washer to counter.
8, Pull out DW and lay on its side to expose bottom of dishwasher. disconnect the motor terminal plug. and disconnect the temp prope.
9. disconnect the drainage tube and then proceed to remove the 3 plastic clips that hold the pump housing to the tub.
10. I used some silcone grease around the new pump housing to be safe. then I installed the new pump housing and motor in the reverse order.

It probally took me about an hour start to finish, the hardest part was placing new housing back in. The ring around the bottom of tub is very sharp!
Left some blood there.

Dishes were not cleaned properly, residue

  • Customer: Francis from Baltimore MD
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Wrench set
  • 8 of 10 people found this instruction helpful
I had removed this part several times before, it had clogged from sediment, so I had practice. That issue was resolved, but I determined the water level during the wash and rinse cycles was low, and the valve appeared to be the culprit. The trick is to remove the valve from the bracket, removing the single screw, and sliding the unit so the tangs on the bracket can be pushed to the rear and then towards the front. When you disconnect the electrical connection, then the valve can be pulled out towards the front for better access and to disconnect, if your supply hose is long enough. That makes swinging the wrench easier. Other wise it is tedious. Make sure to reapply thread tape after reconnecting the supply hose.

No power to dishwasher

  • Customer: John from Chula Vista CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 7 of 7 people found this instruction helpful
First I shut off the breaker for the dishwasher. I had to remove the 6 screws that hold the top part of the dishwasher door to find the panel with the fuse. Then following the instructions that came with the new fuse I cut the wires from the old fuse to remove it. Next I installed the new fuse and attached the wires and then replaced the screws. Turned the breaker back on and everything worked great.

motor was very loud...........bearings in motor were beyond repair

  • Customer: Mark from Plymouth WI
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
  • 12 of 23 people found this instruction helpful
Replace motor/pump assembly

dishwasher wasn't fully draining at end of cycle

  • Customer: Richard from Naperville IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Wrench set
  • 9 of 14 people found this instruction helpful
Removed drain hose to ensure no blockage in drain. No blockage, then removed drain pump cap (where drain hose attaches to drain pump) with allen wrench. Push tab in on drain pump and twist counterclockwise, drain pump came off. Reversed to attach new pump and it works.

Pulverized food particles were being left on the dishes in the top rack

  • Customer: nanette from Bronx NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench set
  • 8 of 12 people found this instruction helpful
FIRST I TURNED OFF THE POWER GOING TO THE MACHINE!!!! Then I removed the top rack by removing the (2) end caps on the front of the rack glides first then lifting the rack upwards and out. Next I removed the bottom rack which slid out easily. I then removed the lower spray arm that was held in place by the plastic turn-screw portion of the lower spray arm support/hub. I turned the screw a few times and the spray arm was released. I then released the feed tube assembly that was held in place by (2) clips; one clip was on the back panel of the tub (above the probe area) and the other clip was on the top panel of the tub (before the upper arm spray). Then I turned the entire tube feed assembly a quarter turn to the right so that it was possible to separate/unsnap it from the feed cap on the bottom. After the feed tube was moved away I was able to access all (4) screws that holds the accumulator in place. I used an allen wrench to remove those. After the accumulator was removed I saw two screws that was holding the 2-part protective cover of the chopper assembly. The small cover came out easily, the round cover took a little jiggling and fussing until I figured out how to pop it out. The chopper was revealed when the cover came off and I found it to be very warn and a bit bent. I pulled it out by pulling it upwards and forward towards me. At this time I also removed the valve check. To my surprise it didn't look like the one that I bougth to replace it. It was missing the round disk portion. I fished around thinking it may have somehow fallen off, but I didn't find anything. I put the new one in, disk-side down. I then put the chopper assembly in place and put everything back together again. I'm not 100% sure that it is completely back to normal. It seems to leave significantly less debris than before, but I noticed that there is more water on the bottom of the basin now. So it may not have been my only problem. If anyone has experienced the same thing I would really like to know

dishwasher wasn't cleaning well

  • Customer: Robert from Katy TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 6 of 6 people found this instruction helpful
Pulled everything out the front, and dug down to find a thrashed chopper assembly (like a little garbage disposal). The previous owner just tossed anything in; pop tops, plastic cutlery, etc.
Didn't pay attention to the exact installation of the chopper as I pulled it out, but, it turns out that it only goes in one way.
Used pictures and instructions I found online as a guide and didn't have any issues.
Replaced the check valve because it isn't expensive and I was in the neighborhood.

bones inside locked motor up and burned it out

  • Customer: Dawn from New Richmond WI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set, Wrench(Adjustable)
  • 6 of 6 people found this instruction helpful
disconect water supply and drain hose, unscrew 2 screws hoding front of dishwasher to countertop, slide dischwasher out so you can tip on its door and remove 1 screw hidden behind plastic shield and pull motor out install in reverse order.

large leak on start of wash cycle , water leaked at bottom of door

  • Customer: robert from danvers MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 7 of 9 people found this instruction helpful
I removed the screws around iner door panel. this allowed me acess to the hex head screws holding the plastic
air inlet and replaced it. the small tabs on the ends of the old inlet had bent
up allowing the water to flow by

quit pumping water

  • Customer: Robert from West Middlesex PA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 6 of 6 people found this instruction helpful
I removed the dishwasher from under the counter. This took the bulk of the repair time along with disconnecting the water supply and electrical connection. I had enough slack in drain hoses that I could turn the dishwasher over to replace the motor. I was surprised that there was only one bolt that held the motor in place. I put the motor on, turned the dishwasher upright and slide it back unde the counter and began the long process ofreconnecting everything. I am sureit could have gone faster if I were younger and did not need glasses for close work. Start to finish took me four hours. This was the fourth time I have replaced motors in dishwashers of various makes.

Wheel mount broke on right side of top shelf. Shelf not supported.

  • Customer: Warren from Wantagh NY
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 7 of 10 people found this instruction helpful
I order a pair of wheel mounts and replaced both. Squeezed ends of plastic "plug" on the front edge of each rail (top shelf) and removed plug. slid out top shelf, snapped off old whell mounts, snapped on new wheel mounts, slide shelf back into track and re-inderted end "plugs". Done!

Lower spray arm seal replacement

  • Customer: Fred from Grafton OH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 8 of 13 people found this instruction helpful
Remove upper tray and spray arm. Remove two screws retaining pipe for upper spray arm and overhead. Unscrew retainer on top of lower spray arm and remove. Gently rotate the upper feed pipe clockwise until pipe can be removed from lower pipe. You may then remove the lower pipe and bearing housing where the seal is. Reverse order for reassembly. I also replaced upper spray arm bushing. Very simple, remove one screw and the arm will come out.

Door would not remain closed stopping the cycle.

  • Customer: David from New Baltimore MI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 6 of 7 people found this instruction helpful
After replacing the door latch which was not faulty I learned fron a local appliance repair company the door was distorted as a result of an earlier failure of the cable assembly breaking. The door opened with such great force hiting my leg and apparently distorted the door or machine frame. The fix was to bundle a towel and place it between the door and dishwasher sides, one at a time, and forcing the door in a closing direction to bend the door and frame. After several attempts the door now closes well and remains shut during the cycle.

Broken Door Links

  • Customer: Randall from Moreno Valley CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 6 of 7 people found this instruction helpful
Remove two screws at top that fasten dishwasher to cabinet. Slide dishwasher out to expose the two links that attach the door to the springs. Fit the new links to the springs and door.

Replace old leaky door seal with replacement part

  • Customer: Bob from Lake Forest IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 6 of 7 people found this instruction helpful
I peeled off the old seal and replaced with the new seal. The instructions were clear and easy to follow, however the new seal made the door not stay closed as the friction catch at the top was no strong enough to overcome the tension of the door closed with the new seal.

There were explicit instructions on the way the seal was to work with the sealed edge spreading into the tub area as the door closed. I was very careful to follow those instructions and made sure to seat the seal carefully. After I reinstalled the seal three times to see if I could get it to seat properly, as a last ditch effort I reversed the seal to the opposite way the instructions indicated and it worked with the door closing properly and the seal didn't leak.

Based on looking at the old seal and how it was originally installed, I actually think the seal was out of spec for the unit. However, if it isn't leaking that is what it's all about so we will see how long it holds.
All Instructions for the KUDP01FLSS6
76-90 of 737