Quick Question!

Have you ever purchased from PartSelect.com before?

Models > KUDI24SEBL1 > Instructions

KUDI24SEBL1 KitchenAid Dishwasher - Instructions

All installation instructions for KUDI24SEBL1 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KUDI24SEBL1
571-585 of 596
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dishwasher wouldn't drain

  • Customer: Roy from Powell, OH
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Turn off the breaker to the dishwasher - there will be water very near the motor and other electrical components. I first scooped and towelled all the water out of the bottom of the dishwasher. The drain valve can be accessed from the bottom front of the dishwasher without pulling the unit out from under the counter. There were 4 screws to remove the 2 bottom metal panels. Next use pliers to loosen and slide back the hose clamp connected to the drain. Have a towel ready and pull the drain hose off the white check valve. The check valve can then be removed by unscrewing it - you may need to use pliers. Put the new one on and everything back together.

sprayer arm had detiorated

  • Customer: kathleen from shorewood, MN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Followed instructions and did repair before my husband came home! EASY!!!! WISH ALL WERE LIKE THAT!

I had to replace the spray arm.

  • Customer: Diane from Park Ridge, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The video on this website made removal and installation a breeze. Just watch and follow along.

Replace damaged control panel Touch Pad

  • Customer: john from Lecanto, FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Carefully lift one corner of old touch pad and then pull off with care. Remove old adhesive on surface with WD-40 .You may need to utilize a flat headed tool like a screwdriver to scrape of any hard areas of old adhesive.When surface is clean fit new pad carefully in place making sure you align pad correctly before pressing into place.

Dishes not clean and soap dispenser not completely rinsed out.

  • Customer: James from Trafalgar, IN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I looked in the bottom of the dishwasher after browsing the website regarding possible solutions. When I removed the bottom spray arm I noticed three screws missing from the pump housing. The loose pump outlet had allowed the seal to push out. Ordered-Normal shipping on the part.

Dishwaster was leaking when running.

  • Customer: Brian from Virginia Beach, VA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
1. Removed lower dish tray. 2. Removed old gasket by pulling it out. Came out easy. 3. Cleaned gasket track of food particles with toothbrush and rag. 4. Found center of new gasket and installed new gasket by starting at the top center and work around track pushing gasket in until seated. 5. Tested and no leaks.

Leaking

  • Customer: Robert from Nuevo, CA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
Thee dishwasher came apart very easy, had no problems. Found out where it was leaking around the seal. Ordered parts and they arrived very promptly. Had a few little glitches when I was putting it back together. One of the screws stripped and a larger screw solved the problem. I have a lot of patience, so it worked out fine. Bob.

parts wore out

  • Customer: Dennis from Kingsport, TN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
followedinstructions videos

Water supply tube rotted out.

  • Customer: Irene from Wagoner, OK
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
First step was done BEFORE I received the parts. I had to squeeze the clips at the face of the drawer slides, then slide them up through their slot. This allows the top rack to slide free for removal. Flip the rack upside down for access to the single holding screw. Screw off and remove all parts, note their sequence. You phone people can take pictures! When I got the parts in the mail, it took all of ten minutes to run through this procedure. The dry run sure helped, and I hope this helps you. One part WAS different from the original but was easily figured out. The keeper part was split instead of a pass thru. Pry it carefully open and slide the tube in place. Piece of cake! A lot of new parts for the $, well worth it. Works like new! Enjoy, glad to help. Mike

UNABLE TO OPEN DISHWASHER DOOR! Door handle broken

  • Customer: Roger from Washington, MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Shut off circuit breaker to dishwasher (DW). Using a 1/4" nut-driver, remove the base kick-panels and DW front panel and foam insulation block. Then, using a small flashlight and mirror (or you can lie on your back and look up), move the broken door handle aside enough to see a pathway straight up into the front of the machine, centered in the latch opening. You'll see a rectangular shape, a little bigger than 1" in size up there (mine was grey). Then, slide a 8"+ long thin screwdriver (3/16" tip, or less) up until it contacts the "square" and gently push upward. If you hit the right thing, you'll feel it flex (if it doesn't flex, keep probing). Keep pressing up and it will unlatch the door. It's a little challenging, but worth the effort. There is no other way to unlatch the door. After the dishwasher is opened, then you can remove the top panel using the #11 Torx driver (4 screws). You'll need to then unplug the "ribbon" and 2-wire connectors to the control panel so that you can work on that panel which holds the handle ass'y. You can remove the broken latch and reinstall the front and continue to use the dishwasher (turn 'breaker back on) while you wait for your parts to arrive promptly from "PS". There are no electrical hazards in that area to get touched. You'll just need to use that screwdriver to open it each time. YOU CAN DO IT!

Dishwasher quit working one day. No warning of any other problem.

  • Customer: Bo G from Madison, AL
  • Difficulty: Really Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
First thought it was the latch with associated switch. However it turned out the front cover of the dishwasher with the plastic attachment pods were all broken preventing the latch switch from properly being held in place and preventing its function. Installed a new cover ($70.) and the machine works like new again. A cautious note: Never grab the front cover to move the dish washer this will break the attachment pods and prevent the latch switch from working properly.

Upper dishrack rusted out

  • Customer: June from Camarillo, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Watched the video and did it.

Started making loud noises during wash cycle

  • Customer: Jerold from WASHINGTON, UT
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
After reviewing the troubleshooting tips for this model I ordered in the Wash Arm bearing ring and the spray arm seal. The old ones I removed didn't appear broken, but when I replaced them all the noises went away. Simple (couldn't be simpler) inexpensive (about $10.00) repair.

Dishwasher making a noise (lower area)

  • Customer: Fernando from El Paso, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
I reviewed your video and followed the steps, I appreciate the video. I used the tools described in the video; it was a simple process. Thank you Parts Select. .

Needed to replace middle spray arm of dishwasher

  • Customer: Joan from Merrick, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
It was so simple. Before odering the parts I had watched the video online and it seemed very easy to do. So I bought the parts (which arrived literally 2 days later) and followed the video instructions and within 10-15 minutes the repair was done. I was really thrilled and know that I saved myself a lot of money in the process. Thank you for providing such great service.
All Instructions for the KUDI24SEBL1
571-585 of 596