KUDC10FXWH0 KitchenAid Dishwasher - Instructions

Lifted out the old damaged cap; replaced it with the new one. No tools needed. It took one minute. The company had the part sent out to us immediately; it arrived within a few days. The whole process of ordering, receiving, and repairing was super convenient.

First I shut off the power and the water then I disconnected the drain hose. Then I removed the dishwasher from under the counter and turned it up side down. I remover the pump retaining screw turned the pump, removed it. installed the new pump reinstalled the retaining screw. and reinstalled the dishwasher under the counter. I reconnected the drain and water then turned on the power. the dishwasher is working great. Thanks PartSelect for the fast delivery and the right part.

I removed the screws on the inside of the door. Removed panel from the outside. Disconnected the power wires to the panel. Disconnected the wires to the latch switch. Removed the latch assebly. Put new assembly in place. Connected swtich wire. Connected panel wire. Put panel back on dishwasher door. Installed panel retaining screws. Job Complete!

I replaced both brackets and cords. the hardest problem was attaching spring to frame housing of dishwasher since I didn't want to pull dw completely out of cabinet area because of water copper line connection and power connection. I had to use grip plyers to hold spring as I streached spring to connect to cable.

took the bottom sprayer off to reach the chopper assembly.Then took out the old one and put the new one in. It works like new!

The dishwasher made a loud grinding sound when it ran. We looked at new dishwashers and they're still basically the same, but the $$$ is so high. We looked at the reports PartSelect.com and after reading the reports, decided it was the pump motor/impeller unit and ordered it online. FIRST, read all the other installation stories. It will save you time. You will save unnecessary steps. In the end, it wasn't actually as bad as it sounded. So, here are the steps I took to install the new pump motor with impeller unit. ONE: turn off the water supply TWO: turn off the power (I had a dedicated circuit breaker just for the dishwasher)THREE: disconnect the water supply at the pipe(not the dishwasher) FOUR: Disconnect the drain hose at the drain(not the diswasher)FIVE: remove whatever screws are holding the unit inside the base cabinet SIX: pull out the diswasher(carefully watch the wires, hoses and insulation) SEVEN: tip the dishwasher forward (lay it on rags, watch for water)EIGHT: Disconnect the electrical supply plug to the pump (it's a plug-type connection, squeeze the edges to release)NINE: remove the one bolt holding the motor on the pump assembly and the heat sheild(you'll need a ratchet with extension) TEN: turn the pump motor counter-clockwise and pull it off. ELEVEN: align the arrows on the new motor of the pump and mounting assembly. TWELEVE: clean the o-ring on the pump and lubriate with drying agent THIRTEEN: place the motor on the pump assembly rotated counter clock-wise a bit past the bolt hole and press until it seats. FOURTEEN: turn the motor clock-wise to engage the locking mechanism and align the bolt hole. FIFTEEN: replace the bolt and heat shield. SIXTEEN:reconnect the power plug SEVENTEEN: tip-up the dishwasher, slide the unit back under the cabinet. EIGHTEEN: reconnect the drain, water, and power. NINETEEN: turn-on the water and restore the power TWENTY: test(start a wash cycle) the unit to be sure it doesn't leak. TWENTY: if all is good, replace screws holding the dishwsher in the cabinet(otherwise you will have to back-track to find your error - I didn't). And that's it! Now it's running smooth and silent, just as before. Good luck!

First challenge was getting a model number match. The telephone parts ordering rep convinced me to get a ...SS6 replacement. Said his database did not show the ...SS7 installed in my home. As to how I did the repair, I looked at the video available as a part of ordering the replacement parts. The video seemed quite appropriate and accurate except that spring tension was under-stated in the video. In fact, it was made to look like there was no issue in reconnecting the tension springs. Not! Took some effort and a bit of wrestling in a difficult body position to reconnect the tension springs. On the other hand, all of the self-replacement task far beat paying an exorbitant house visit fee by an authorized repair person.

Slide dishwasher out (two screws holding in place) unscrewed screw on roller wheel. Popped out bad wheel and popped in new one. Re-strung rope line around roller wheel(s) and slid back into place. DONE! 5 minutes!

I watched a video that should how to take the motor and housing assembly out. I ordered a part from a competitor, but it was the wrong part ( This was after putting in my Kitchenaid model number). The thermodor opening was too big. Unfortunately, no one was able to help me find the right part. i search online again and found partselect.com. I was able to find the exact part right away. I was thankful that they had a better picture to make sure I got the right part. My part arrived within a few days. My husband was out of town for the week, and I was tired of washing dishes. My husband had taken pictures of the motor and wiring. I asked him to send me the pictures. I was happy to have the pictures to make sure the wiring was correct. I had great success installing the motor and housing assembly by myself. No dishes in the sink tonight and no leaks! I should have been a plumber instead of a teacher. I installed the dishwasher 8 years ago. I also installed the garbage disposal. I have watched too many repairmen fix my appliances for hundreds of dollars. I have always thought "I can do that! " ... so now I do.

I loosened the screws and removed the old parts and replaced them with the new ones. This is not the first time I have completed a repair on the dishwasher I also replaced the chopper and the main water line last summer. My dishwasher runs like new. Thank you part select for delivering the parts in a timely manner. I ordered the parts late the night before and they arrived at my door in a couple of days.

I spent a heck of a lot more time contemplating how this was going to go than it actually took to do the job! Great insights from other people (and Steve's videos are awesome!). Absolutely agree with the person who said the replacement links are of better quality than the originals. I expect I'll never have to do this again. Bought the link kit and the springs since I didn't know for sure what the failure was until I got into it. The original springs were fine so am returning the two that I bought. Trickiest part was re-hooking one of the door springs - I couldn't pull the dishwasher all the way out due to length of the electric wiring, so had to work at a weird angle to do one side. They're so strong that I kept pulling myself across the floor instead of stretching the spring! Finally ended up starting with the inside end hooked and then stretched to make the connection to the link. That said, including removing the kick plate and counter anchors and then replacing them, I was done in less than 30 minutes.

The dishwasher was so load I was sure the pump had a bad bearing. . . After reading the on line comments I examined the chopper and it looked ok. As it turned out the damage was on the shaft and caused the shaft to lock onto the screen without the ability for the spring to work it must have caused excess pressure making the loud noise. I replaced the chopper and now the dishwasher is very quiet again. To replace I took out the baskets and four screw on the big screen and one more screw on the chopper cover then I had to pull on the chopper with moderate force and install the new one . Then I put back the covers and basket. . . Very easy

Installed brackets

The part was easy to install. But , you might have to unhook electrical, water, and drain. That is the time problem, part install is easy. All I had was a socket set, 1/4, drive fits. But a nutdriver would have been easier. WATCH the install video, great info!!!!!

Remove power to the machine. My particular installation did not require physically removing water and drain lines. Remove the dishwasher from the cavity. Put a towel or two down on the floor. Lay the washer on its face on the towels and this orients the motor in the up position on the bottom of the washer. CAREFULLY unplug the motor wiring harness but if possible, leave the heating element connection in place as spade connectors tend to lose their grip with multiple engagements. Remove the single bolt located between the motor and stainless bottom of the cavity that locks the motor in place. Leave it in the cardboard shield, that really helps in reinstalling it. CCW rotation of the motor disengages it from its housing. Work the motor straight up and out of the housing. This was the most difficult part of the entire process due to the metal housing not quite clearing the plastic pump housing where they mate, but its do-able. Nothing should have to be forced. Now you have the motor in hand. Be very attentive how and what order you disassemble. Remove the back of the motor housing to block the armature to remove the impeller. DO NOT NICK THE FIELD WIRING IN THE MOTOR. I believe the threads were left hand but I don't remember the rotation. They do tighten in the direction of the motor rotation though. Carefully pry the seal out of the pump housing with many short lifts as to not mar the housing itself. Added a little dishwashing detergent on the outside of the new seal and carefully pushed it into place with the end of my screwdriver. Don't cut yourself on the metal insert in the center of the seal.Reassemble the impeller to the shaft WITH the spacer that comes with the new impeller kit. Make sure the impeller is tightened down completely to the end of the threads to insure proper clearances when reassembled. Don't force or over tighten. You'll feel a positive stop. Reassemble the motor to the housing Lubricate the housing o ring seal on the outside with a VERY small amount of dishwashing liquid lest you create a suds factory on startup. Replace the holding bolt on the pump housing. Reconnect the motor leads and heater element if removed. Stand the washer back up. There will probably be water around the door area from the pump when the machine is returned to the upright position. Reconnect lines and check under the pump housing for leaks while in operation being careful not to get into moving parts or electrical connections. Good luck.