KUDC03IVWH0 KitchenAid Dishwasher - Instructions

1. Place a towel in the bottom of the dishwasher to keep anything from falling in the drain. 2. Release the clamping bracket on each side of the water line that the spinner kit is attached to, so you can pull it down a little to get the old spindle out of the hole. 3. Take the old spindle out. 4. Put the new spindle in. 5. Push the spinner wheel onto the new spindle until it you hear it snap into place. 6. Push the water line back into the bracket until you hear it snap into place. 7. Tug on the spinner slightly to make sure it is secure. 8. Done.

parts were correct, fit perfectly, easy and straight forward replacement, thanks , vidoe was very helpfull

Purchased Bi-metal fuse and installed as per included instructions and video on site.

After attempting to change the "high limit switch" to no avail, I researched further and found that doing a reset/reboot cured the problem.The instructions for the high limit thermostat were a bit off, as there was no screw to remove, only a spring like bracket that I did not try to figure out. The work area is so tight if the dishwasher is not removed and tilted that I thought it best to look for alternatives prior to pulling it out and disconnecting power and water. So ... voila, it's fixed with a reset only. Reset is accomplished by pushing two buttons 5 times. "high Temp Scrub then Heat Dry, high temp scrub then heat dry etc, until you click them both 5 times.It will go through cycles for a few minutes, then after done, run the dishwasher as normal and test if fixed. There are a few different ways to do it depending on the model.

Replaced the old rack with a new one. Saved about $30.

I had to pull the dishwasher out from the cabinets about 12" in order to pull the old seal off. Installing the new seal was quite easy, since there is no adhesive necessary. Start at the top center of the replacement seal and snap the groove of the seal which is hard plastic, into the mating parts of the tub and the tub trim. Its a little hard to explain, but pay attention to how the original seal (W10179427) was installed.

Lifted out the old damaged cap; replaced it with the new one. No tools needed. It took one minute. The company had the part sent out to us immediately; it arrived within a few days. The whole process of ordering, receiving, and repairing was super convenient.

repairman replaced the valve inlet; first website tried to tell me I needed a new pump, but repairman said it would be some type of valve; service rep on phone very helpful,I ordered the correct part,except for having to lay on the floor, he repaired it easily; part came within 24 hours. Worked immediately. No additional tubes or parts needed.

To access the handle assembly, the control panel must be removed. Remove six (6) torx screws (T-20?) from inside of door, being careful to support the control panel, as there are small wires between the door and the control panel assembly. Carefully remove what remains of the broken handle so as not to damage the mounting pegs. Snap the new handle carefully in place. I took the advice of Thomas from Austin, TX and added a second spring to the other side where pegs exist on both the handle and the control panel assembly. I used needle nose pliers, as it is a little tight trying to get the small spring on the pegs. Place the control panel back in position and reattach using the six torx screws removed previously. Overall repair time was less than 10 minutes. The handle does have a more "reliable" feel having return springs on both sides.

I read information on this website about the function of the high limit thermostat. I found that it was the problem by disconnecting the two wires on the thermostat and straight wiring to bypass it. This allowed the machine to work properly so I ordered the high limit thermostat. To replace the part I used a screwdriver to remove the instrument panel and replaced the high limit thermostat by disconnecting the two wires from the old thermostat and connecting the wires to the new thermostat. I then replaced the instrument panel. My machine is working properly again..

First I shut off the power and the water then I disconnected the drain hose. Then I removed the dishwasher from under the counter and turned it up side down. I remover the pump retaining screw turned the pump, removed it. installed the new pump reinstalled the retaining screw. and reinstalled the dishwasher under the counter. I reconnected the drain and water then turned on the power. the dishwasher is working great. Thanks PartSelect for the fast delivery and the right part.

The dishwasher was so load I was sure the pump had a bad bearing. . . After reading the on line comments I examined the chopper and it looked ok. As it turned out the damage was on the shaft and caused the shaft to lock onto the screen without the ability for the spring to work it must have caused excess pressure making the loud noise. I replaced the chopper and now the dishwasher is very quiet again. To replace I took out the baskets and four screw on the big screen and one more screw on the chopper cover then I had to pull on the chopper with moderate force and install the new one . Then I put back the covers and basket. . . Very easy

off with the old, on with the new.

Used a video to guide me.

Removed 6(six) torx head screws backside of top control panel. Removed top of panel to access contol board. Unplugged clearly marked wire plug-ins. Unsnapped control board, snapped new board in ressymbled panel.