Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The Dishwasher had a no power symptom
I researched the internet about this symptom on the Kenmore Elite Dishwasher and I found lots of people with the same problem. Everyone fixed it by replacing the Bi-Metal Fuse. I removed the old fuse and tested continuity and it was indeed bad. Once the new fuse arrived I tested continuity and it of course worked as expected, so that was a nice wipe of the brow. The new Bi-Metal Fuse came with a nice instruction manual. I also used a video from YouTube to help with the repair as well, but the included instructions were enough. The only thing that was not clear was the best way to attach the new wire since it was quite a bit longer than what was orginially there. So I ended up just folding it up and putting everything back together and it worked just fine. This repair was very easy as long as you are OK with cutting and stripping wires in a somewhat confined space and not being too worried that you might mess it up for good... :)
Motor starting making a terrible racket after installation 15 months earlier
Be sure to shut off power at circuit breaker and disconnect drain and water supply. Remove the dishwasher from the cabinet, lower it on its side. Remove three electrical connections from motor to various sensors. Remove three plastic wedges that secure the motor gasket to make a tight seal. The motor pops into the body of the dishwasher for removal. The replacement motor goes in just as you took it out. It took two people to set the motor right to ensure the good seal on the gasket for re-installation. Then turn it back upright and secure it in place. Couple suggestions, be sure to have ample towels around for leakage from water and drain lines. Be sure to cover the bottom of the dishwasher during disassembly and reassembly of the wash manifold. I dropped a screw in there and it took me some time to fish it out. All in all, it went well. Don't pay a plumber for this job. I'm a clod and if I did it, you can.
disconect water supply and drain hose, unscrew 2 screws hoding front of dishwasher to countertop, slide dischwasher out so you can tip on its door and remove 1 screw hidden behind plastic shield and pull motor out install in reverse order.
removed 6 screws removed upper console of door and swapped out broken handle with new one. installed required spring and closed up console of door. real easy it took less than 15 minutes .
The Spinner at the top of the dishwasher came off and would not stay on.
First of all I appreciate the instructions provided by this site when I selected the part I needed! The installation was so easy. I popped the end caps off of the top rack guides and removed the top rack. I reach in and popped the clips holding the top sprayer bar and gently pulled down on the sprayer bar enough to place the spinner button in the top of the sprayer bar. Then pressed the spinner on the bottom of the sprayer bar into the button I place in the top of the sprayer bar and reattached the sprayer bar to the clips. Put the top rack back on the guides and replaced the guide caps and it was finished. Easy fix thanks to this site great instructions!
Pliers, Screw drivers, Wrench (Adjustable), Wrench set
7 of 12 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dishwasher door would close but not latch
The door catch clearly was not acutating correctly when the door handle was depressed. I removed the 6 screws (star pattern, not phillips) from the top of the door to allow access to the door handle and catch. the door handle is made from a thin and poorly constructed plastic piece with two arms that attach to the body of the latch. The latch has an electrical switch that has two wires attached to it. Note the location of the wires before you disconnect them. remove the latch assembly and door handle together. Remove the damaged door handle. Note where the return springs are located on the handle and latch. Replace the new handle on the latch mechanism, attach the springs, put the complete mechanism in the door and replace the screws. Finding the problem took 5 minutes and the remove of the top of the door. Waited 4 days for the part, 10 minutes to install the new part and back in operation
Factory crimped end of link cord pulled out of plastic fastner that hooks on door.
Removed 2 screws that fasten dishwasher to underside of countertop. Pulled dishwasher out from under the countertop for access to sides. Hooked link on door, threaded cord around 2 wheels, hooked spring to back of dishwasher, stretched spring and hooked to eye on end of link cord. I found it very difficult to hook spring to link then try and stretch spring to hole at back of dishwasher. Easier to pull spring and link towards each other and connect. Note: This link was actually different from the original. The plastic end that connects to the door actually hits the first wheel when door is closed but it doesn't seem to prevent the door from locking properly (old design was better). However, I shaved this plastic end to provide better clearance.
I simply had to hook up the power cord to the dishwasher so i could plug it into the outlet rather than direct wire the appliance. Everything went very smoothly. Everything needed for installation other than tools was provided. Easy to follow instructions if you know a little about electrical wiring.
