Quick Question!

Have you ever purchased from PartSelect.com before?

Models > KUDA03CTBL2 > Parts

KUDA03CTBL2 KitchenAid Dishwasher - Parts

All parts for the KitchenAid Dishwasher KUDA03CTBL2

Below is a list of all parts for the KitchenAid Dishwasher KUDA03CTBL2. To find the repair part you need, you can browse the list below or you can narrow your choices by searching for a part by name or description.

All Parts for the KUDA03CTBL2
1-14 of 199
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$17.53

Door Balance Link Kit

This part is a door balance link kit, also sometimes known as door cable or door spring cable kit, that helps support the door as it opens and closes by connecting to the dishwashe...

$5.07

Tine Pivot

The tine pivot clip, also known as the tine row pivot, is used in dishwashers and is located in the upper dishrack. The clip is used to keep the tine row in place in the dishrack. If your clip is cracked or damaged, it is best to replace this part. To repair, first lift the release tab and hold the other side to prevent it from falling off. After lifting it off, you can set the new clip on the tine row and lock it up. Refer to the manual provided by the manufacturer for further installation instructions and guidance. Remember to wear work gloves as a safety precaution.

$46.26

Silverware Basket

This is a basket for washing flatware or silverware in your dishwasher.

$17.71

Chopper Assembly

This part chops up/mince the food particles to prevent from clogging the dishwasher pump.

$6.12

Rack Track Stop

The rack track stop on your dishwasher is designed to stop the dish rack at the appropriate place when opening and closing the rack. If your dishwasher is not cleaning your dishes ...

$11.43

Mounting Bracket

The mounting bracket is sold individually, without screws. This part secures the upper side of the dishwasher to the underside of the counter or cabinet to prevent the dishwasher from moving, shaking, or tilting forward. The bracket is made entirely of metal. It is recommended to check all brackets, if applicable, because they often wear at the same rate and both may need to be replaced. This is an OEM part that is sourced from the authentic manufacturer. Tools needed are a pair of needle nose pliers and a screwdriver.

$19.54

Bi-Metal Fuse

This part is used as a safety device to protect the dishwasher circuit from overload. If the temperature gets to high it will shut off the electrical current to the heating unit i...

$26.28

Tine Row

The tine row on your dishwasher rack divides the rack into columns to keep your kitchen items in place during the washing cycle. If you notice that one or more of the tines on your current tine row is damaged, you should consider replacing it. This product is made of gray plastic and is approximately 21 inches in length. This tine row contains 11 straight tines and 1 curved tine. This product is sold individually. Many of our customers have rated this repair as very easy. To complete this repair, simply remove the old tine row and replace it with the new one.

$15.03

Spinner Kit

This is also called the 3rd-level spinner. This part works like a little spray arm at the top of your dishwasher.

$15.70

Rinse Aid Cap

This part holds the rinse aid liquid in the dispenser until the timer activates the rinse cycle.

$51.16

Water Inlet Valve

This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the d...

$4.89

Rubber Washer

The rubber washer is a part which is specific to dishwashers and should not be substituted by a similar part. It works with the heating element to seal the receptacle opening where the heating element is attached. The rubber washer is used to prevent water leaking from your dishwasher during its cycle. Before making any repairs to your dishwasher make sure that you disconnect the power by finding the breaker for the dishwasher, and turning it off. The tools you will need to complete this repair include an adjustable wrench, and a 1/4 inch nut driver. This specific rubber washer is sold individually.

$136.44

Circulation Pump and Motor

The circulation pump and motor is located near the bottom of the dishwasher. The part functions by spinning the impeller of the circulation pump, which is used to move the water th...

$7.00

Spray Arm Seal

This seal is located between the spray arm and the water feed tube.

All Parts for the KUDA03CTBL2
1-14 of 199