Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Unwanted water.
A Mouse friend had seen fit to chew through the original drain line. I used my Model Number, and was able to order the correct part . It arrived the next day. The job itself is fairly straight forward. You will need to access the rear of the machine. This may include shutting off, and disconnecting the water supply line. (Adjustable wrench). Mine is under the sink, on the "Hot" side. You may also need to un-plug the unit. (recommended) . A pair of (Pliers) will be needed for the spring clamp.
My dishwasher's heated dry cycle wasn't heating up
After pulling the dishwasher out from under the cabinet, I found it underneath near the back right side. I disconnected the old thermostat, unscrewed the clamp holding it into place, put the new thermostat in, screwed it back in and replaced the two plugs. Then I pushed the dishwasher back into place, and it initially didn't work until I found an online forum that was able to identify the reset command for my dishwasher (for the WDT710PAYM4, press any three buttons in a sequence of 1 2 3 1 2 3 1 2 3. After completing that all the lights lit up, and I shut the door leaving it for half an hour) Once the reset finished, the heated dry worked like it was suppose to.
1.Check the lines for any obstruction. Gunk can easily build up. I have used the dishwasher for approx. 10 years. I do rinse/scrap dishes prior to loading. 2. Drain all remaining water. 3. Unplug the dishwasher. 4. Grab a towel and proper screw driver. Unscrew the bottom protective plate. Remove the insulation plate. 5. The drain pump is located to the bottom left. Have your towel under it. Unplug it gently. Turn counter clockwise to remove. 6. Install the new drain pump (reverse order) 7. Return the insulation plate. Screw back the bottom protective plate. 8. Plug in
Lost stop from one side of top rack. Rack could be pulled off track.
Looked at other side of top rack which still had the stop. Just had to orient the direction of the stop and push it firmly onto the rack arm. Took a couple tries, but it went in and locked. Works perfectly. Inexpensive and easy fix to to very annoying problem.
Unplug dishwasher and slide it out from under cabinet. Remove old broken link (a heavy string between two plastic parts) and replace with new one. Slide dishwasher back and plug it in. Very easy and no tools required.
The old seal would often travel with the door when opened.
I removed the old seal and carefully cleaned the track into which the seal was fixed. No tools other than some ordinary cleaning liquid, cloth and small wooden piece to swab out the track. Easy and quick. As a note here, I first used the incorrect schematic for the unit and ordered the wrong seal. However after receiving the wrong part, I made the correction and reordered. I did this over the phone as I needed instructions to return the part. The person taking my order and answering my questions was very helpful and I want to take this opportunity to thank her.
Tried to clean old part and it did not work. Ordered the new part on Saturday and received it on Tuesday. Removed the old part and installed the new one. Ran the machine and it worked great. A big savings on not having to buy a new machine!!
I opened yutube and noted the tips on how to fix specific problems with my dishwasher. That "steve" guy was very helpful. I tested the old bi-metal fuse with no flow and ordered a new replacement through partselect. The part arrived in one day and was fitted quickly. I used the teat meter to confirm that the fuse was ok before I installed it. The only problem that I had was identifying the part and number from a diagram which I did not have.
front seal on the old pump failed causing the front bearing to get wet repeatedly and fail
Removed required hardware and dishwasher from undercounter mount. Turned dishwasher on its front and removed the old motor. Installed the new motor and tested for function. Installed once test was successful.
Just removed the old seal and followed the instructions that came with the new one. Since the old one didn't have any adhesive on it ,I didn't use the adhesice on the new one. Problem solved!
the tines in the upper basket of the dishwasher were falling apart
Removed the old tines by pushing out the clips on the end and then installed the new tines and applied clips - took 10 minutes worked slick and the washer basket looks to be brand.