Quick Question!

Have you ever purchased from PartSelect.com before?

Models > KSCS25INSS00 > Instructions

KSCS25INSS00 KitchenAid Refrigerator - Instructions

All installation instructions for KSCS25INSS00 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the KSCS25INSS00
766-780 of 1,075
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Installing Part for Ice Maker

  • Customer: Larry from Weeki Wachee, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Simply done !

The icemaker stopped making ice.

  • Customer: Paulette from North Canton, OH
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Called an appliance repair service, they wanted $326.69. Went on line, ordered the part, it came in 2 days. It took me 20 minutes to remove and reinstall the part. The sound of the cubes dumping into the bin was great. Thanks for your how to do it video. Oh by the way, I am a 68 year old handy woman!

Ice maker would not harvest ice (ice still frozen in ice maker)

  • Customer: Leonard from Hot Springs Village, AR
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I removed ice maker from mounting rack but left wiring connected. Checked power between N & L: 120V (OK). Shorted T & H: no harvest cycle. Shorted L & V: no water came out to fill tray. Shorted H & N: heater did not turn on. Also noted that LED on right Electronic Control Board would flash 2X, then pause, then 2X, then pause, regardless of flapper position on left Control Board. Replaced Icemaker Control Assembly first (also purchased replacement Control Boards). Icemaker started working. Noticed that original Control Boards still worked the same way (LED flashing regardless of flapper position) BUT ONLY IN CERTAIN STAGE OF CONTROL BOARD CYCLE. At other times in cycle, LED would turn steady on when flapper closed, and right after tray fills with new water, LED does not light at all. Apparently this is NORMAL. I ended up not replacing old Electronic Control Boards. Icemaker took 3 days to totally refill ice bin - I presume this is also normal.

refrigerator was making a knocking sound just before icemaker quit working.onl

  • Customer: Jesse from North Chesterfield, VA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
online PartSelect had instructions for replacing icemaker. I gave them my part # and they sent me the correct replacement. following their instructions I was able to install the replacement in 30 minutes or less. PartSelect is a good company to deal with.

Stopped making ice

  • Customer: BOB from HOCKLEY, TX
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I order the suspect part before pulling out the ice tray and whole ice maker for inspection. As it turns out my ice tray was peeling and all gunked up and I needed a new one. I suggest in the case of ice maker issues that you pull the entire ice maker before ordering what appears to be the troubled part. I had to replace the whole ice maker which was not really that much more money than just the part.

ice maker was not working

  • Customer: LINDA from FARMINGDALE, NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I called in a repairman, who wasn't sure what the problem was but suggested it "might" be the electronic control boards. He charged me $55 for the service call, which I initially thought was reasonable. Then I found your website purely accidentally. I watched the video several times and read all of the comments posted. I then decided I would wait to see what the repairman would quote me for the part and the additional labor charge. He told me the part was $125. and the additional service charge was another $75. I decided to order the part, which arrived in 2 days. I am a woman who has never repaired anything on my own, but I decided to take a chance with this. It took me about 20 to 30 minutes to install both parts and within a few hours the first ice cubes fell. I was so proud of myself and very pleased that I found your website. The price of the part was reasonable, the video was very straightforward and all of the comments were extremely helpful. Thank you.

No Ice Production Nonstick Surface In Tray Pulled Off

  • Customer: Joe from Paducah, KY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Open freezer door remove swinging door above icemaker for access to icemake and it simptly pulls out with some resistance ( no screws ) then you can unplug wire connecion remove old icemaker take new icemaker plug in connector slide in to bracket attached to icebox line up water outlet reinstall swinging door and wait for ice production. . . . . Easy breezy

No ice

  • Customer: Sheila from Hayward, CA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Watched video then repaired very easy since I have extreme RA in my hands.

Ice dispenser door hinge inop

  • Customer: Robert from Emory, TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
1. Remove the ice-maker/water dispenser cover plate located on the freezer door, by: inserting a putty knife blade at the bottom and freeing up the two retainer tabs; then pushing up. (note: be careful pulling the cover plate, there are many electrical connections on the back).

2. Note the electrical connections on the back of the cover plate and locate the connect close to the inside of the freezer door and disconnect it. (Note: this is much easier than pulling each wire off its connection point and then having to remember which color coded wire went where).

3. Carefully work the door hinge pin back out to the right and remove it and the hinge (Note: in my case the pin was already half way out so the old door couldn't close - and since this model door had a heater which came on because the door was misaligned there was constant flow of warm upwards causing ice to melt, run down and re freeze thus making the door difficult to open).

4. Unscrew the single her head screw holding the small metal piece to the right that retains the know upon which the outer door frame turns. Move the frame to the right to free it and work it out if the way. You now have access to the ice-maker door and hinge pin assy.

Ice maker was not making ice

  • Customer: William from princeton, WV
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
used the video on your web site. also read the overview made things really simple

In the Door Ice Maker stopped working

  • Customer: Ed from Germantown, OH
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the instructions on the information sheet provided as well as watching a demo video on YouTube. Actual replacement of the emitter and receiver boards took only 5 minutes, but I was not sure it was working till I could here the ice maker harvesting the cubes. Still wanted to be sure so I kept an eye on it for a few hours. Each time I looked in there was more ice. I am so glad I found your website. Parts were about $106. Labor would have cost that much and the repair guy I talked to on the phone said he would probably have to replace the whole unit.

Would not produce and dump ice fast enough to use.

  • Customer: Roy from Ocala, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Used the trouble shooting off of YouTube and after finding that the heater was not at the right resistance, ordered a new ice-maker and installed. Very simple and a lot cheaper than going through Sears.

replaced ice model

  • Customer: Joanne from Big Flats, NY
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Watch the video was very helpful. I'm just a women and I did it all by myself. Thanks for the help of the video.

No Ice,No Water

  • Customer: JIM from MADISON, SD
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Turn ice maker control off,hold up front cover remove two screws, remove cover, remove rear screw on the back right side, slide unit part way out, make sure flipper on left is out of the way, unplug connector on right, remove unit,remove bottom cover & put on new unit,install in reverse order, turn ice maker control on, done

my ice maker quit working several montyhs ago

  • Customer: Olan from Plant City, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I went on line and found your web sight. There was a list of the parts by number and I clicked on the rilght one. It brought up a video for repairing it myself. It was so simple. I just followed your instructions and within an hour I had ice. It makes so much ice I'm going to have to give it away. No really its great.
All Instructions for the KSCS25INSS00
766-780 of 1,075