Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Difficulty removing old switch.
Everything went as planned except the cold temperature (freezer door switch located inside freezer) made deflection of the switch locking tab difficult to remove. Letting the switch warm up was not an option.
Refer lights not working, there are two lights and neither worked. Decided the switch was the problem.
The switch fix but did not fix the problem. I assumed the wires go on the same way as on the old switch. Is it possible if one light Burns out, the other will not work either?
We removed the old switch, unplugged it, plugged the new one in and it was easy to do. But when we tried to put the switch back in we had a very hard time doing it. Eventually got it in, but if it had not been for the difficulty we had getting the new switch to snap in to place, it would have taken under 5 minutes.
Once I got a part that wasn't broken in transit (took them sending it 3 times for that to happen), it was a breeze. Remove old drawer, take tracks off old drawer and place on new drawer. Put new drawer in fridge.
Small water leak from cracked fitting leading into water reservoir fill valve.
Remove some shelving and have a towel handy. Opened water filter door to expose two 1/4” screws. Removed 2 screws. Placed my hands firmly on upper panel and gently pulled/tugged panel forward and slightly down. Disconnected roof lighting clip. Removed panel from frig. Disconnected both ends from solenoid fill valves by pressing in the colored locking piece to release tubing while pulling tube out. Cut zip ties and removed old leaking reservoir. I also removed the straight reservoir seeing as the part I replace was redesigned and the other one was not needed. Put new zip ties in place. Slid the new part into position and pressed the ends into the solenoid valves. You do not need to press in colored locking pieces, they will self lock. Secured with zip ties. Grabbed a container and filled it up with water through the door to fill and purge and check for leaks. Reconnect light clip, reinstalled top liner and snapped into place. Put screws in. Closed filter door. Took about 15 minutes. I did watch a you tube video prior to attempting this repair myself.
I thought this was going to be much more difficult than it was. Take the bottom access door off (using a small socket - same size for all screws). Disconnect the plug to the motor. Unscrew the 4 screws holding the motor. Take the motor out. Unscrew the shaft screws on top (only 2) so you can manipulate it if need be up and down or spin it. Insert new motor and make sure shaft is seated correctly into the motor head. Screw motor back in. Screw shaft back in. Plug up motor. Screw bottom door back on. You are done. EASY!! Took me about 10-15 minutes to do. Much easier than most things.
Light rocker switch broke and refrigerator light couldn't go on.
I just popped out the old switch with a flat head screwdriver. Removed the connections and then installed new switch by reversing steps. Popped in back in and the light went on.
Had to push the light switch to get lamp to light up. Removed power from refrig. and removed old light switch and replaced with the one I got from Partselect. Turned power back on and was done.
Repair was tremendously easy. All I did was remove old light switch by prying out with screw driver and plugging in the new light switch and pushing it into the hole. Simple! The instructions weren't needed, but they were very thorough.
The best part of the repair was how easy it was to find and order the part. Instead of searching the parts houses around town I just went to the PartSelect web site, quickly found and ordered the part in about five minutes, received the part the next day at my home and was ready to make the repair. Wow! What a pleasure for something to work the way it was meant to. Removed old switch located by prying out with sharp knife or screwdriver. Don't worry about breaking it or cracking plastic. Disconnect(unplug) wires from back of switch. Replace (plug-in) wires on back of new switch. Insert in location of old switch. Finisheed.