Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Pan is easy part, fan motor assembly is appliance orgami
Remove back cover Remove drip thing from top to tray in the back Remove fan motor assembly. This is squirrely. Top bends towards you, bottom pushes in to the unit. Not fun. CAREFULLY remove copper tube that rests on drip tray Remove tray - there are clips in the front that get released by screwdriver Clean up Replace new tray Replace copper tube Play with fan motor assembly till it fits. It doesn't look like it's gonna work until it does. See youtube videos on this. Replace drip thing from top to tray - I forgot this one the first time. Replace cover.
This is a simple, but squirrely, repair. Right on the border of easy (because so few tools and steps) and A Bit Difficult because of the patience required.
Unscrew decorative plastic cover. Unsnap old damper assembly and disconnect wire connector. Snap in the new assembly and plug in the wires. Replace decorative cover.
Remove the 2 screws that secure the flipper seal to the door. Slide the entire flipper seal up approximately 3/8ths of an inch. Disconnect wire connection. Reverse procedure to reinstall. Be sure flipper seal is pushed down enough to align screw holes before trying to reinstall the 2 screws.
I got really tired of taking food out covered in icicles and stabbing a huge block of ice out of the bottom. Turns out all he needed was a little wheel with cogs and I looked up the sticker model number on this site and clicked the part of the fridge. So simple, wish I would’ve done it sooner.
Once the part arrived, which was very quickly BTW..all I had to do was remove the old filter and then just screw the new one into place....Now I just happen to be both female and blonde but was able to get the job done in less than 15 minutes (that includes opening the box) and with very little water dripping from the old filter!!! Looks like I could work as the Maytag repair woman soon!!
AS PER A VERY GOOD VIDEO I FOUND SIMPLY BY SEARCHING FOR THE PART NUMBER. IT MAY HAVE BEEN ON THIS SITE. SADLY, THE PUSHING ON THE CONNECTOR WITH THE 1/2" WRENCH LOOKED A LOT EASIER IN THE VIDEO, OTHERWISE EASY PEAZY AND I HAVE VERY PAINFUL ARTHRITIS IN MY SHOULDERS.
Frost on the edges of the freezer and all around the freezer door
I was getting small sections of ice and a snow like build - up around the freezer door. I thought that the door was not sealing tight enough and that the cold air was leaking out. The original door gasket appeared to not have any flexibility anymore and was getting hard. I ordered a new door gasket from PartsSelect. When the gasket arrived it was in a large enough box and that saved me some time as the gasket was not "crushed" to the point where there were a lot of kinks in the gasket. I used a hair dryer on low to warm the gasket and stretch it out some. The freezer door required me loosening four small screws and lifting the door off. I placed the door on an old blanket so not to scratch the finish. It was easy to remove the old gasket and after doing so I cleaned the track where the new gasket was to go with isopropyl alcohol, Once cleaned, I placed the gasket over the channel in the door where the old gasket had been and started installing the new gasket. I started at the corners and you can feel the gasket snap into place. Once the four corners were done I started at the top and installed the gasket the rest of the way. You can feel it snap into place. as you work your way around the gasket channel. Once the gasket was in place I placed the door on the four small grooves where the door had been and tightened up the screws. I made sure that no white from the inside of the freezer door was showing after the gasket was in place and that the gasket had some "spring" to it. The door was back on, the gasket was tight and it appeared to be a good seal. Around 12 hours later I checked the freezer and there was no more ice or "snow" on the edges of the freezer. While the gasket was not inexpensive, it is a genuine OEM piece, and the gasket is a lot cheaper than a new refrigerator! I hope this was helpful...
the locking latch to the water filter cover had been broken for a while
Open the existing cover and carefully with the thumb and index fingers, pry the cover at over the left pin and remove the cover. Place the replacement onto the right pin and pry the left placing it over the left and you are done.
Remove the Veggie shelf top. Remove veggie tray. Pull the clip on the center of the left panel - lift and pull forward. Install new panel by inserting the two guide pins at the rear of the frig and move the panel to a 45% angle so you can install the veggie lid pin into position before moving the panel down into the secure position. You will hear the clip seat into position. If you do not do this I am not sure how the lid pin can be installed without breaking it.
Empty box sent with no part!!!! No customer service help because of covid
No product was sent in the box for the shaft I received an empty box from them cannot perform any repairs because I got no product from this company. Called customer service said due to Covid no customer service available when online and receive no customer service no refund no product no help
