KPDJ630Y0 KitchenAid Dishwasher - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Pump flow rate insufficient to drain tub completely
I watched the video then followed the procedure accessing the impeller/grinder from inside the tub. Had I not watched it, I would have torn into it from the bottom by removing the motor, etc. with disastrous results. I was quite depressed when installation of the impeller kit did not resolve the problem. I remembered from the survey that 56% of problems were solved with this kit; BUT, another 24% found that the check valve on the discharge line was the problem. So I removed it and lo and behold, it was partially plugged with broken pieces from the old impeller. The 1 page sheet that comes with the kit is simply a diagram of the parts included, there are no instructions ---- watch the video!!! All said and done, my experience with PartSelect was first class. They are 5 Stars in every category and I would highly recommend them.
Parts Used:
-
Jeffrey from Lewis, NY
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
the plastic roller axles had become brittle, and were breaking, dislodging the little wheels that guide the lower rack in and out of the unit smoothly
broke off the remaining roller axles, pushed the new roller axles into place, then snapped the little wheels onto new axles. I FELT LIKE WONDER-WOMAN, FIXING MY OWN DISHWASHER!!!
Parts Used:
-
sarah from MELBOURNE, FL
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
Was this instruction helpful to you?
Thank you for voting!
After cycle was complete dishes were still dirty
followed the basic instructions / diagram supplied, however the impeller was fused to the shaft. Used high speed cutter to remove old impeller and sandpaper to clean up shaft.
Parts Used:
-
DOUGLAS from SNOVER, MI
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Socket set, Wrench (Adjustable)
Was this instruction helpful to you?
Thank you for voting!
Rubber Delivery tube for upper rack acquired a crack or hole in the tube
Repair was really easy. Tube is flexable so it was just a matter of pulling it off each end where it was attached and replaced the new one.
Parts Used:
-
Telford from Weidman, MI
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Upper rack conduit tube came loose and melted on the heating coil
-
Jack from Scarsdale, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Split supply tube for upper spray arm
-
Patricia from Newton, KS
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Top rubber water delivery tube leaked due to old age.
Zip zip zip. It is done. Removed old part. Heated new hose with hair dryer to make it more flexible. Slipped new hose in place.
Parts Used:
-
John from Massapequa, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
leaking badly & not cleaning dishes
You need a properly sized hex (Allen) wrench to get the screws out. Basically simple: remover bottom roller tray, unscrew large plastic holding bolt, remove lower spray arm, unscrew bolts (be sure the wrench is sized right or you might strip the heads), and replace gasket; then reverse procedure. Chances are if the gasket was bad, it will be very obvious (out of circular slot and stretched).
Parts Used:
-
Eric from Ritzville, WA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!