Quick Question!

Have you ever purchased from PartSelect.com before?

Models > KHWS02RWH2

KHWS02RWH2 KitchenAid Washer - Overview

Get Parts and Repair Help for KHWS02RWH2

If you know the washer repair part you need, you can browse the list of all parts on the KHWS02RWH2, or you can search by name or part description. You can also find your part by where it is located on the KHWS02RWH2 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for KHWS02RWH2 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$154.13

Drain Pump Kit

This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. This part is used on front load models.

$7.22

Touch-Up Paint - White

18ml

$31.73

Suspension Springs - Set of 2

Sold individually.

$11.07

Spray Paint - 12 oz. - White

$20.86

Shipping Bolt Kit

This kit includes both the upper and lower shipping bolts. 4 in total.

$363.18

Electronic Control Board

This part helps with the tumble and spin cycle. If your motor won't run in either the wash or rinse cycle or if the fuse on the board is blown, then you have to replace this part. The fuse is not sold separately. NOTE: Motor is sold separately.

$88.92

Washer Dispenser

$16.61

HOSE

$27.43

SCREW-KIT

Inner Tub

Spider and shaft are included and are NOT sold separately.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Bellows were moldy, needed to replace

  • Customer: Franck from Annandale, VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 271 of 288 people found this instruction helpful
The first step is to remove the retainer ring that holds the outside of the bellow in place.
To do this, Open the washer door as far as you can to get it out of the way. look underneath of the front of the bellow on the outside of the washer where it meets the door. Put your head almost on the floor and look up.
You will find a spring streached... read more

Washer would not drain ,F02 and SUD code displaying

  • Customer: Donald from Wichita, KS
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Socket set
  • 180 of 185 people found this instruction helpful
(1) First I unpluged the washer then I removed the water from the tube with a water vac.(2) Then I removed the three (3) screws that holds the front panel, using a Torx T-20 socket. ( this is a front load washer ). The panel is below the loading door.
(3) I packed towels under the washer.
(4) I slowly removed the cleanout in the front of the p... read more

front load washer latch replacement

  • Customer: James from Vilonia, AR
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 135 of 154 people found this instruction helpful
1. remove the three screws from the top backside of the top panel
2. push the top panel to the rear 1/8 to 1/4 inch
3. lift/rotate top panel from rear to front, set aside.
4. remove the three wire connectors from latch.
5. use #15 Torx to remove the three screws from the latch.
6. remove and replace part using top opening.
7. r... read more