KGYS977EZ0 KitchenAid Dryer - Instructions

Determining the problem was the hardest part. With multiple parts (coils,thermostats...)possibly causing similar symptoms, I narrowed it down to the two coil valves.
Un plug the dryer. Remove two screws at the base of the front panel. Turn the front panel 180 degrees to avoid disconnecting the door switch. Gas valve with coils on top are on the right in front. Remove two screws in bracket holding coils, disconnect the wires, replace with new coils and reconnect wires. One coil has 2 terminals the other has 3 no chance of crossing the wires. I used an offset/right angle screw driver for one of the bracket screws due to close proximity to the drum. A stubby phillips head will work. You can check the burner operation with the front panel off as long as the door switch is still attached. Swing the front panel around and lift back into place securing with the two screws. Dryer works fine now.

This repair was a cinch. Pliers to pull out the metal piece and a screwdriver to pry out the 'catch' part in the door. Both replacement pieces went right in. I cannot believe how easy and CHEAP this fix was, and I'm so glad I found this site!! I figured I would have to call a repairman and pay big bucks, so I put it off, but the door was getting worse--slamming it so hard to keep it shut. Again, thanks for this great site.

-unplugged appliance
-removed lint trap
-removed 2 lint trap shute screws with phillips screwdriver
-popped open top of appliance with standard screwdriver by applying pressure at each front corner so that it could be tilted up to access actuator switch on right side of door
-removed 2 actuator switch screws, located on upper right side of laundry door, with phillips screwdriver (screws are accessed from outside of door frame not through appliance top).
-discarded broken actuator spring (accessed from open appliance top)
-replaced new actuator spring
-replaced 2 actuator switch screws
-closed top
-replaced 2 lint trap shute screws
-replaced lint trap
-plugged in appliance
-tested for operation
-kissed by happy wife

After looking on the website for advice I walked throught the simple steps of disassembling the front, removing the drum, removed the back, disconnected the wire harness. Then removed the blower housing in the back. The blower, mounted on the back side of the motor was very tight. I used a pipe wrench wedged in place and help by my 10 year old Grand-daughter while I used an adjustable wrench to turn the shaft on the front of the motor. Spun the blower off, removed the two clips holding the motor. Then reversed the process when I received the new motor. Care should be taken to avoid damaging the blower fan if a lot of pressure is required.

couldn't get blower wheel off of the motor. really tight. rounded off the wheel's square hub while trying to hold it still as I turned the motor shaft out. No, I wasn't turning it the wrong way :) I ended up going to the back of the dryer and using the multimax to quickly cut the wheel away from the hub. I love that oscillating saw! Just for fun, I put the motor in a bench vise and got the wheel hub off (in pieces). VERY tight! Ordered new wheel, and the job was smooth sailing from there on. I am guessing that experienced repair people automatically order the motor and blower wheel at the same time(?) BTW both parts were perfect matches for the originals. Not surprised; this has always been my experience with partselect.com!

I removed the two screws holding the front panel to expose the lower works and verified the heating cycle failure. After a check of the vent system, checking the sensors for continuity and coils for resistance, I retired to the 'net for support. Accepting the general consensus that the most frequent, common and likely failure to be the coils, I rechecked them with the meter and found the two pronged coil to have significantly more resistance than the three prong coil. That was enough evidence to point to the coils. While I waited for the part to arrive, I replace the vent ducting. When the parts arrived I removed the two Phillips screws holding the coils, removed the old ones, installed the new ones, replaced the bracket, put the front cover back on and in less then ten minutes clothes where drying.

Started out taking the back off, then found online that access is from the front and much easier to get to. Simply pop the hinges in the back of the top panel and then the front of the top is popped off. From there, it is easy to remove the old belt, clean the innards (found 31 cents) and replace the new belt. It was a little disconcerting to see the idler pulley laying loose inside, but the diagram showed exactly how to put it back in place, with the new belt keeping it in place.

The new lint filter fits perfectly,however because the handle is much larger than the original it does not allow the filter to close completely...causing a small amount of lint to acummulate on the dryer top.

I did NOT have to repair the latch on the actual door, just the small metal piece that it hooks on (on the dryer itself) and it took about 10 seconds to.....do it myself. Just used needle nose pliers so squeeze the piece together and fit it in. thanks

I read a fix-it article from another contributor and followed those instructions to the T. Pull out lint trap, remove the two screws. Slide the top cover towards the front and prop it up with a mop handle.
Unscrew two screws in the door switch (with the door open) - Oh, to keep from killing yourself unplug the dryer just in case. Take pliers and pull the plug apart. It will be right in front of you in the right corner at the top. Plug new switch into that plug, reinstall the switch by reinstalling the two screws you removed. Snap top back into place and reinstall the two screws at the lint trap. Oh, don't forget to clean the trap and slide it back into the unit. Now you have earned that beer.
Put tools away and proudly show your job off to the wife telling her how difficult it was.

1 Unplug power.
2. Remove the front of the unit by removing the two screws at the bottom of the front panel. Front dryer panel will swing out from the bottom and then the clips will release the top of the panel, careful not to disconnect the dryer door switch. ( can be unplugged to remove the front panel out of the way.)
3. Looking inside the unit on the right side you will see the gas value. On top of the gas unit you will see two small coils the coil closest to the burner has two leads on it. Remove the two screws to get to the coils, remove the medal plate, remove the connector then lift off the secondary coil. Replace and test. You can test unit with the front panel off. (be careful). If no heat, check that the Flat Style igniter is glowing. (ohm out both coils) before ordering parts. Intermittent heat problems. I replaced the secondary coil, it did ohm out o:k but it had swollen and was very tight on the shaft.

This was my first dryer repair, and it was so easy. Simply pull out the lint trap and unscrew the two screws that are exposed. They attach the top deck of the dryer to the drum.

Once it's unscrewed, pull forward while lifting the top of the dryer. The top is attached to the control assembly. They should both lift up, but you'll need something to prop it up like you would the hood of your car.

Next, use the pliers to pinch the connector so that you can separate the two parts of the connector.

Open the dryer door to gain access to the screws that hold the switch in place. Use your screwdriver to unscrew the switch.

Plug the new switch connector in, and close up the dryer.

Word of caution; there are sharp edges inside the dryer so be careful.

First I took the front of the dryer off then located the igniter. It only required removing two screws, removing old igniter, replacing with new igniter, and replacing the two screws.. While I was replacing the igniter I took the drum out and throughly cleaned the inside. Lucky me, I found 85 cents on the floor of the dryer. I am 65yrs old, married and mother of two.
This was easy to do and sure saved money. I reccommend others try to do repairs for themselves and using PartSelect was less expensive too.

After unplugging the dryer,I removed 2 bolts on the back top of the dryer, then removed the two screws in the lint box area. I used a screw driver to help force the top panel of the dryer up. When open, I removed the top screws that held the front and side panels together. I then lifted the front panel up and away from the dryer, so there would be room to take the drum out. I removed the belt from the pulley (located under the drum) and slid the drum out. I removed the old seal, cleaned up the drum and the inside of the dryer, then glued the new seal on. After the glue was dry, I put the drum back in (with the belt on the drum), put the belt back on the pulley and proceeded to put the dryer front back on. Once the front was on, I put the top back on and replaced the bolts on the back of the dryer. I plugged it in and it is working great! By the way, before this, I had NEVER attempted to repair a dryer before and I am female. If I could do it, so can anyone else willing to try :)

use screwdriver topry plastic out plyers to pull out metal latch put new parts in