Quick Question!

Have you ever purchased from PartSelect.com before?

Models > KEYS850LQ0

KEYS850LQ0 KitchenAid Dryer - Overview

Get Parts and Repair Help for KEYS850LQ0

If you know the dryer repair part you need, you can browse the list of all parts on the KEYS850LQ0, or you can search by name or part description. You can also find your part by where it is located on the KEYS850LQ0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for KEYS850LQ0 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the KEYS850LQ0

[Viewing 3 of 3]

Manuals & Care Guides for KEYS850LQ0

Click to download
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$14.56

Multi Rib Belt - 92-1/4"

This multi rib belt is an important part in your dryer, it is what helps rotate the drum. The belt attaches to the drum, idler pulley, and motor pulley. As the armature of the moto...

Order within the next 1 mins and your part ships today!
$14.81

Door Switch - 3 Wire

A door switch is a simple on/off switch mechanism that prohibits the dryer from operating when the door is open. This part may need to be replaced if you find that the dryer is not starting, will not shut off or the door will not close properly. All you will need is a putty knife and a Phillips screwdriver. Pry open the top of the dryer, remove the two screws underneath the lint collector without removing the entire thing, unplug the switch, remove the screws that hold the switch place, take out the old switch and install the new one by screwing it back into place.

Order within the next 1 mins and your part ships today!
$14.96

Thermostat, Internal-Bias

A cycling thermostat is in tune with the temperature of your dryer and regulates it in order to maintain a certain temperature. This thermostat reaches a temperature of 155 degrees...

Order within the next 1 mins and your part ships today!
$3.56

Door Catch Kit

This is a door catch kit, and it is designed for use with your dryer. On your appliance you will find both a strike and a catch, these two parts work together to keep your dryer door closed. This kit includes two strikes, three catches, and a set of instructions. Each of the door catches included have a different tension. Make sure you use the one that matches the existing catch on your appliance. All three of these are color-coded, and have a number on the back. The instruction sheet will tell you which catch you need to use for your specific model type.

Order within the next 1 mins and your part ships today!
$36.87

Thermal Cut-Off Kit

The thermal cut off turns off the heating component when the dryer overheats, ensuring there is a consistent level of heat at all times. This dryer thermal cut-off kit includes one...

Order within the next 1 mins and your part ships today!
$45.43

Maintenance Kit

This maintenance kit or dry repair kit is used for dryers. The kit includes the drum belt, drum support rollers, one idler pulley, four tri-rings, and one clip. If your dryer is making loud, squeaking, and squealing noises while the drum is turning, or the drum has stopped turning, using this maintenance kit is the solution. The tools needed for this installation project are: putty knife, Phillips screwdriver, 5/16 nut driver, and a small flat blade screw driver. This kit can be used for gas and electric dryers. Remember to unplug the dryer from the power source before beginning this project.

Order within the next 1 mins and your part ships today!
$12.47

Rear Drum Support Roller Kit

The drum support roller kit allows the dryer to tumble properly by supporting the drum cylinder. The kit includes two drum rollers, four tri-rings and one palnut (or retaining wash...

Order within the next 1 mins and your part ships today!
$10.04

Idler Pulley Assembly

This part provides the tension required for a multi-ribbed belt. It also serves to help the belt to rotate the drum and attaches to the idler pulley wheel. If your dryer will not start or tumble, takes too long to dry, or is noisy during operation, you may need to replace the idler pulley assembly. Make sure to disconnect power before installing this part, and work gloves are recommended to protect your hands. While the dryer is disassembled for this repair, consider replacing the drive belt as well. You will need a putty knife, a Phillips screwdriver and a 5/16 nut driver for this repair.

Order within the next 1 mins and your part ships today!
$5.77

Tri Ring

If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found b...

Order within the next 1 mins and your part ships today!
$5.00

Heating Element Connection Wire Kit

This kit is used for electric clothes dryers, and it comes with a yellow wire nut.

Order within the next 1 mins and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

door switch was bad

  • Customer: pat from lisbon,, OH
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set
  • 904 of 926 people found this instruction helpful
i was able to go on line with your company , find my dryer, order the part and had it the next day. fast , great , service read more

Dryer tub belt broke

  • Customer: Ray from Denton, TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 832 of 884 people found this instruction helpful
Removed the two screws that attatch the lent channel to the top of the dryer, then lifted the top of the dryer by pushing in on the two locking tabs located at the front , left and right , corners of the dryer top with a small flat head screw driver. The top of the dryer will fold back out of the way. At this point I removed the two 1/4 inch screws that are ... read more

No Heat

  • Customer: Vernon from Niceville, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 808 of 857 people found this instruction helpful
First tried heating element and thermal fuse with no luck. Ordered thermal cutoff and fixed problem. Had I used an ohm meter first I would have determined problem before having ordered heating element and fuse, as both had resistance. I wast just lazy and ordered the took the most common failed components first before taking dryer back off. read more